web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
#27198 06/01/12 04:52 PM
Joined: Jun 2012
Posts: 1
TaT Offline OP
Member
OP Offline
Member
Joined: Jun 2012
Posts: 1
I recently acquired a "never installed" Ernest Telecom D3 payphone and I would like to use it in my home. I have it open and have tried connecting it to my line but it refuses to respond in any way.
The battery was dead on the smart board and I have replaced it.

I would like to find any documentation, wiring diagrams or advice on how to get it operational.
At this point I would be happy to hear a dial tone!

Please advise. Thanks!

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Nov 2012
Posts: 1
Member
Offline
Member
Joined: Nov 2012
Posts: 1




I have a D3 that I have had running for several years. It is currently connected to my Asterisk system via a Sipura PAP2 ATA. The coin controller works quite well, even from the reduced line voltage provided by the ATA.

I have instructions for attaching an LCD display to the connector on the control board. This is quite easy to do and allows programming most features from the keypad. The LCD also displays call progress messages and coin deposit requests and total coins deposited. I leave mine connected andmounted on the inside of the phone for quick programming changes, but it could be mounted externally in a project box.

I also had to replace the backup battery and coin switch. The switch was only about $5.00, as I recall. I also wired up a ringer from an old Western Electric 500 set to the ringer connector on the board. The D3 board has the capacitor needed for the ringer.

I also have the D3 manual and programming software that can be used to remotely program the phone. The software requires a 1200 baud connection to the internal modem of the phone. I configured an old modem to lock the 1200 baud connection speed with AT commands. I then connected the modem to anothe ATA port and called the phone via Asterisk using the D3 software. I was able to completely program and backup the phone with this method.

My phone came with an installed rate table file. Unless you have a way to create a new table, there is no way to change this with the software. Instead, I populated rate table "override" values with the software to get the rates I wanted for my local area. This works fine for all numbers, except international numbers.

Let me know if you want the Windows software, manual, and LCD instructions. I can email to you in a zip file.

Don

Joined: Jan 2013
Posts: 1
Member
Offline
Member
Joined: Jan 2013
Posts: 1
I have an Ernest payphone and I am looking for the software and manuals to program it. How can I tell which model it is? I can not find a model on it anywhere. It is touchtone with no display. It works fine except it answers with the modem when someone calls the house after 3 rings. I would like to change that so that my answering machine picks up before the payphone does. Can anyone help with manuals and programming instructions?

Joined: Mar 2013
Posts: 1
Biz Offline
Member
Offline
Member
Joined: Mar 2013
Posts: 1
I just picked up a Ernest D3 and haven't been able to locate a manual or the programming software anywhere. I would really appreciate you sending me copies of them and your LED instructions if you would.
Thanks,
Bob

Joined: Oct 2013
Posts: 1
Member
Offline
Member
Joined: Oct 2013
Posts: 1
Hello, I have a payphone with the D3 board, if you could email me the manual and software, that would be of great assistance. I can't find either anywhere. Any advice on setting up the payphone for home use also appreciated. This looks a little complicated.
-Timm

Joined: Feb 2006
Posts: 1,716
Member
***
Offline
Member
***
Joined: Feb 2006
Posts: 1,716
There are two ways to program the D3. The first is to acquire the LCD module that attaches via ribbon cable to the board. You do the programming via keypad.

The second is to acquire the T2 remote program and program the phone via modem and computer.

Rcaman


Americom, Inc.
Where The Art And Science Of Communications Meet
Joined: Feb 2015
Posts: 1
Member
Offline
Member
Joined: Feb 2015
Posts: 1
I would love it if you would send me a copy of the software and how to hook up lcd display!!! Thanks in advance Delmar

Joined: Feb 2006
Posts: 1,716
Member
***
Offline
Member
***
Joined: Feb 2006
Posts: 1,716
PM Sent

Rcaman


Americom, Inc.
Where The Art And Science Of Communications Meet
Joined: Jun 2010
Posts: 201
Member
Offline
Member
Joined: Jun 2010
Posts: 201
Rcaman, may i get the same info please?

Thanks

Joined: Feb 2006
Posts: 1,716
Member
***
Offline
Member
***
Joined: Feb 2006
Posts: 1,716
PM Sent

Rcaman


Americom, Inc.
Where The Art And Science Of Communications Meet
Page 1 of 3 1 2 3

Moderated by  MooreTel 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,697
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,100 Shoretel
187,712 CTX100 install
186,800 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 11
TDKs79 8
teleco 4
Who's Online Now
0 members (), 140 guests, and 24 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5