web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Joined: Aug 2002
Posts: 1,068
Likes: 1
jsaad Offline OP
Member
OP Offline
Member
Joined: Aug 2002
Posts: 1,068
Likes: 1
i have a 200D with a 480 port configuration, it's a hotel, G1005. customer complains that after they dial a number, they have to wait up to 1 minute for ringback. I've heard of this problem before, it's something to do with the ARS.

Any ideas what I should look for, is it in form 26 digit strings?

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Jul 2001
Posts: 1,985
Moderator-Mitel, NEC, Vodavi
*****
Offline
Moderator-Mitel, NEC, Vodavi
*****
Joined: Jul 2001
Posts: 1,985
It could be as simple as a dead CO line.
If this was an existing setup & it used to work, & nobody was adding anything, that's where I would start.
In COS of the trunks you could also look for'limited wait for dial tone'. That might need to be enabled.

------------------
Bound to cover,
just a little more ground.

Joined: Aug 2002
Posts: 1,068
Likes: 1
jsaad Offline OP
Member
OP Offline
Member
Joined: Aug 2002
Posts: 1,068
Likes: 1
i added option for limited wait for dialtone, no difference. The customer has analog lines, if you put your buttset on the line directly the call goes through fine. when you call through the switch it does in fact take at least 45 seconds to hear your first ringback.

I suppose my next step is to delete all ARS and start fresh however the ARS seemed rather simple.

customer claims this started happening recently.

any ideas?

[This message has been edited by jsaad (edited November 14, 2004).]

Joined: Jul 2001
Posts: 1,985
Moderator-Mitel, NEC, Vodavi
*****
Offline
Moderator-Mitel, NEC, Vodavi
*****
Joined: Jul 2001
Posts: 1,985
Don't delete all the ars, just create a new route for a test number. Get that to work, then you can change the other routes.

Joined: Nov 2002
Posts: 632
Member
Offline
Member
Joined: Nov 2002
Posts: 632
When you used your butt set did you dial the pick code first ,then the number ,maybe their provider.

Joined: Aug 2002
Posts: 1,068
Likes: 1
jsaad Offline OP
Member
OP Offline
Member
Joined: Aug 2002
Posts: 1,068
Likes: 1
good ideas, thanks!

Joined: Apr 2005
Posts: 26
Member
Offline
Member
Joined: Apr 2005
Posts: 26
First at all I'm in 2000 not 200 .
If I had a problem like yours I'll try to find out at first were the delay ocurs :
1.at sizing the C.O. trunk ?
2.at dialing on C.O. trunk ?
3.at conecting the audio path between the station and the C.O. trunk ?
To do that I'll monitor with the butt set on monitoring state (if it haven't that state you can made that state by conecting tru an ~100 nF capacitor) an outside test call.
If you findout where the delay ocurs post again.

Joined: Apr 2005
Posts: 26
Member
Offline
Member
Joined: Apr 2005
Posts: 26
First at all I'm in 2000 not 200 .
If I had a problem like yours I'll try to find out at first were the delay ocurs :
1.at sizing the C.O. trunk ?
2.at dialing on C.O. trunk ?
3.at conecting the audio path between the station and the C.O. trunk ?
To do that I'll monitor with the butt set on monitoring state (if it haven't that state you can made that state by conecting tru an ~100 nF capacitor) an outside test call.
If you findout where the delay ocurs post again.

Joined: Oct 2006
Posts: 17
TSS Offline
Member
Offline
Member
Joined: Oct 2006
Posts: 17
I am having the same problem. This is not only on external calls but transferring incoming calls to stations. I also think this is on extention to extention calls. Any ideas?

Joined: Oct 2004
Posts: 1,057
Member
****
Offline
Member
****
Joined: Oct 2004
Posts: 1,057
From the console, do a direct trunk select on all of the CO trunks to make sure you're getting CO dial tone THROUGH the PBX.
99% percent of the time, the trouble is a bad trunk in the outgoing group, as mentioned earlier!
If they all test fine, make a note for which trunks are used when the call finally does go out. That will help you narrow down the possibilities!


www.ResaleSystems.com 24 x 7 Mitel Parts and Free Tech Support
Page 1 of 3 1 2 3

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,696
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,707 CTX100 install
186,794 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 14
TDKs79 8
jc2it 4
teleco 4
Who's Online Now
1 members (Toner), 103 guests, and 241 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5