|
Joined: Mar 2005
Posts: 6
Member
|
OP
Member
Joined: Mar 2005
Posts: 6 |
Let me first say I am not very versed in our Telrad system, but I used to be able to use the attendant console and enter the COS to make changes to an extensions ability to access long distance. Recently every time I try I get a "Please try later" message. I called the company that we have used for service in the past and the guy could only recommend rebooting the phone system. This sounds easy enough but is there any other suggestions? System is a Digital Key BX, I believe version SB6.03 based on what is written on the box itself.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Aug 2003
Posts: 1,281
Moderator-Telrad
|
Moderator-Telrad
Joined: Aug 2003
Posts: 1,281 |
I don't know of a way to program the digital through a phone. Only on the Sysonip. I can't spell it. You need a programing kit. Check with SSphones ------------------ Need cable or other voice/data hardware? Here's your link. Telephone Supplies
|
|
|
|
Joined: Feb 2005
Posts: 439
Member
|
Member
Joined: Feb 2005
Posts: 439 |
Synopsys are the only Telrad system that I know of that you can program through an ext. The system is about 1.5' wide, 6" thick and about 3' tall, dark Gray, and hinges from the right. The Digital Key BX you mentioned is either an 8/18 or an S128 KSU. They are a light grey with Green writing, and sometimes has a cover over the front (where the cards are inserted). Otherwise you will need Dkeybx (PCP Software) and a MAP cord (Cat 5 patch cord with an RJ-45-to-serial connector). E-mail me if you want the program. ------------------ Telradmaniac [email protected]
|
|
|
|
Joined: Mar 2005
Posts: 6
Member
|
OP
Member
Joined: Mar 2005
Posts: 6 |
I think maybe I wasn't clear. I remember being able to hit the program button on the attendant console, then the COS button, then dial an extension # and was able assign a code for day like 01 or 05 and the same for night. Now when I hit the COS button the read out says "Please try later". What could have changed? Other than maybe a power gliche has screwed something up.
|
|
|
|
Joined: Aug 2003
Posts: 1,281
Moderator-Telrad
|
Moderator-Telrad
Joined: Aug 2003
Posts: 1,281 |
The only thing I can think of is The Virtual ext's. Do you canhge the EXT to give acces? But that came in Version 7 or E2E. But I'm not sure. But I don't Think it was in 6. ------------------ Need cable or other voice/data hardware? Here's your link. Telephone Supplies [This message has been edited by tony3866 (edited March 18, 2005).]
|
|
|
|
Joined: Mar 2001
Posts: 7,350
RIP Admin
|
RIP Admin
Joined: Mar 2001
Posts: 7,350 |
What you are talking about is the COS Reassignment and yes you can do it from the Attn Console, if the configuration computer is connected online you will get the Try Again Later, walk back and see if it was left online by chance. It has to be disconnected in order for you to program the COS from the Attn Console.
Russ runs a local service and private tech center. [/url]
|
|
|
|
Joined: Aug 2003
Posts: 1,281
Moderator-Telrad
|
Moderator-Telrad
Joined: Aug 2003
Posts: 1,281 |
Never Installed one and didn't even think that he was talking about the attendant PC. Sorry muligan. Thats why your the man DTMF ------------------ Need cable or other voice/data hardware? Here's your link. Telephone Supplies [This message has been edited by tony3866 (edited March 18, 2005).]
|
|
|
|
Joined: Mar 2005
Posts: 6
Member
|
OP
Member
Joined: Mar 2005
Posts: 6 |
As far as I know we don't have a configuation computer hooked up the system. Only when we have had a service tech. come in have I seen a laptop connected to the box. You're not talking about the IVM computer right?
|
|
|
|
Joined: Mar 2001
Posts: 7,350
RIP Admin
|
RIP Admin
Joined: Mar 2001
Posts: 7,350 |
No, I'm talking about the switch, not knowing what the last guy did with the programming I would suggest you do a re-boot of the switch. If nothing has changed then you should be able to do your COS agian.
Russ runs a local service and private tech center. [/url]
|
|
|
|
Joined: Mar 2005
Posts: 6
Member
|
OP
Member
Joined: Mar 2005
Posts: 6 |
Justed rebooted the switch and now it works.
Thanks
|
|
|
Forums84
Topics94,262
Posts638,697
Members49,757
|
Most Online5,661 May 23rd, 2018
|
|
|
|