web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#242969 02/03/10 09:19 AM
Joined: Dec 2005
Posts: 19
Member
OP Offline
Member
Joined: Dec 2005
Posts: 19
I currently have an SV8100 with a PRI installed serving 4 locations using ip phones. I need to have each location be able to set their own night service. Their incoming calls ring in to virtual extensions at each site via DID. I have been through the night mode options and what I can not figure out is how the trunks get put into night service groups when using DID. I have only 1 outgoing trunk group. Thanks in advance.

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

#242970 02/04/10 02:08 AM
Joined: Apr 2007
Posts: 1,439
Member
****
Offline
Member
****
Joined: Apr 2007
Posts: 1,439
I think it would be easier to cfd the virtual that the DID is pointed at.

You could have a "day" (cfd cancel) and a "night"(cfd set) button on a phone that would just be a speed dial for the set and cancel routine.

Not sure you could do the "night mode" setup without tenants, would get messy in a hurry. Not even sure it could be done.

D

#242971 02/04/10 02:47 AM
Joined: Apr 2005
Posts: 2,498
Likes: 2
Member
*****
Offline
Member
*****
Joined: Apr 2005
Posts: 2,498
Likes: 2
Have you tried 12-05? DID might follow this setting.

One of our installs has 2 company's.
Company A is on a PRI
Company B is using POTS

12-05 and 12-06 did the trick on setting their own night modes.

I know this isn't your setup but it might help in giving you a clue on what to try for your scenario.


We get old too soon, smart too late
#242972 02/04/10 02:50 AM
Joined: Dec 2005
Posts: 19
Member
OP Offline
Member
Joined: Dec 2005
Posts: 19
I did think of setting it up that way as a last resort which I think I am at. I wanted to use actual night service so the offices could see night in the display. I would think that the translation tables would be a little more flexible. I think the night service is pretty flexible until you add in the DID,s with a shared circuit. This scenario is fairly common with my customers. 1 main site with PRI and remote sites using voip sharing service.

#242973 02/04/10 03:10 AM
Joined: Dec 2005
Posts: 19
Member
OP Offline
Member
Joined: Dec 2005
Posts: 19
12-05 is setup and works fine for the day/night mode switching for the stations. The problem comes in when you are using the same trunks/trunk groups for the different night mode services.
22-13 programs the trunk group to translation table for day/night but is programmed by trunk group. It would be great if it was done through translation table.

#242974 02/04/10 03:37 AM
Joined: Nov 2007
Posts: 369
Member
Offline
Member
Joined: Nov 2007
Posts: 369
Look at 22-10, 22-11, 22-13, and 14-05-01:

In 14-05-01 put all trunks in same trunk group.

Now let's say the main number (DID) points to VE 200. In 22-10 -01 "Conv Area1 (day)", set up conversion area 1 as start 1, end 10. In ConverArea 2 (night) set start = 11, end = 20.

In 22-11-01 = Rec'd DID digits,
22-11-02 = Target VE (200 in this case)
22-11-04 = 3 Busy/NoAns
22-11-05 = VM Pilot (or alternate destination)

22-12-01 = 102 VM (or alternate destination)

22-13-01 Trk Grp 1 Mode 1 = 1 (ConvArea1-Day), Mode 2 = 2 (ConvArea2-Night)
When in day mode, the calls ring the VE. in night mode, calls go to VM (or alternate destination).

22-10 sets up the conversion tables
22-11 sets up the DID destinations
22-13 sets day/night handling of 22-10

(I think)


"I didn't do it, and I won't do it again"
#242975 02/04/10 03:54 AM
Joined: Nov 2008
Posts: 953
Member
Offline
Member
Joined: Nov 2008
Posts: 953
I Agree with Doghart, why can't you Just use call frd all to VM. at The main Phone of a Given Office Set up a Night Greeting in the Personel Mailbox of that Station? With a Button to turn it on and off?


"The Only Stupid Question, Is the Question Thats not Asked."
#242976 03/22/10 02:36 PM
Joined: Mar 2009
Posts: 103
Ham Offline
Member
Offline
Member
Joined: Mar 2009
Posts: 103
D.I.D. MODE SWITCHING, I KNOW THIS IS AN OLD POST BUT IT CONTROLS YOUR INDIVIDUAL DID'S REGARDLESS OF WHAT MODE IT IS, PLUS IT COULD SERVE AS A " NIGHT" BUTTON(1) AND IT LIGHTS UP.
I perfer not to use this feature unless a customer is adamant on wanting to see when someone has called their DID and they want a freakin button to light and land on not on there CAP keys and when there is Multiple Nodes with 1 central Voicemail and all different hours.


I am the Big Ham and I approve this message.

Moderated by  ttech 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,695
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,706 CTX100 install
186,794 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 14
TDKs79 8
pvj 4
Who's Online Now
3 members (Curlycord, JBean3329, mongo5150), 107 guests, and 255 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5