|
|
Joined: Dec 2007
Posts: 3
Member
|
OP
Member
Joined: Dec 2007
Posts: 3 |
Hello, this is my first posting and I have a problem with a linksys WIP330 phone on my tadiran system. I can call the linksys phone and can answer and talk with no problem but when I go off hook on the wip phone and dial a four digit ext number I get a busy signal. any help would be appreciated..
John R.
|
|
|
|
Joined: Feb 2006
Posts: 80
Member
|
Member
Joined: Feb 2006
Posts: 80 |
Please make relevant topic...
Did you try what Linksys suggest?
Appendix A: Troubleshooting
Common Problems and Solutions
1. When I make a telephone call, the call doesn’t go through; instead, I hear a fast busy signal.
Go through this checklist until your problem is solved:
• Follow these instructions to reboot your cable or DSL modem, IP Phone, and router:
1. Power off your cable or DSL modem by unplugging its power adapter.
2. Power off the router by unplugging its power adapter.
3. Power off the IP Phone by pressing and holding down the Power button for two seconds.
4. Wait 30 seconds, and then power on your cable or DSL modem by plugging its power adapter into an electrical outlet.
5. Wait 30 seconds. Power on the router by plugging its power adapter into an electrical outlet.
6. Wait 10 seconds. Power on the IP Phone by pressing and holding down the Power button for two seconds.
7. Reboot one of your networked computers, and check for an active Internet connection.
8. Pick up the IP Phone and try your call again.
• Set up port forwarding on your router. You must specify that four port ranges be forwarded to the IP address of the IP Phone.
These four port ranges are as follows: 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP).
_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ | __|_\m/__(-_-)___\m/|_ _ _ |_ _ _ |_ __ _ |_ _ _ |_ _ _ |_ _ _ | _ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |
|
|
|
|
Joined: Dec 2007
Posts: 3
Member
|
OP
Member
Joined: Dec 2007
Posts: 3 |
ok, I have a linksys WIP330 connected to a wireless endpoint and I have the IP address of the PUGW in Proxy IP, Register Proxy IP,and Outbound Proxy Ip of the WIP phone. On Proxy port,Register port, and outbound proxy port I have 0. I am not sure what to put in the Proxy port, Register port and Outbound proxy port.
John R.
|
|
|
|
Joined: Feb 2006
Posts: 80
Member
|
Member
Joined: Feb 2006
Posts: 80 |
_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ | __|_\m/__(-_-)___\m/|_ _ _ |_ _ _ |_ __ _ |_ _ _ |_ _ _ |_ _ _ | _ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |_ _ _ |
|
|
|
|
Joined: Dec 2007
Posts: 3
Member
|
OP
Member
Joined: Dec 2007
Posts: 3 |
Thanks, that fixed the problem
John R.
|
|
|
Forums84
Topics94,284
Posts638,769
Members49,765
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
136
guests, and
315
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|