Business Phone Systems

AtcomCloud Online Store
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Nov 2008
Posts: 5
cmcbd4 Offline OP
Member
OP Offline
Member
Joined: Nov 2008
Posts: 5
Receives calls but dial pad has no tones. There are two wires with factory ends that were taped off coming out of the keypad (orange and lavender) I don't know if that has anything to do with the problem. Any input would be great.

Atcom VoIP Demo
VoIP Demo
Joined: May 2002
Posts: 17,702
Likes: 7
Member
****
Online Content
Member
****
Joined: May 2002
Posts: 17,702
Likes: 7
Anyone have a wiring diagram? Have to tried cleaning the dial contacts?


Retired phone dude
Joined: Jan 2005
Posts: 15,335
Likes: 8
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,335
Likes: 8
OK, here you go. This is for the -DM configuration, but since I doubt you will need A-leads, this should be all that you need:

Dial leads:

OR/BK: Network terminal C with brown switchook lead;

GN: Network terminal F with white switchook lead;

BK: Network terminal RR;

RD/GN and WH: Network terminal R with red switchook lead;

BL: Network terminal B with black handset lead;

WH/BL: Network terminal S (or any blind terminal) with green handset lead and black switchook lead;

RD: Network terminal T (or any blind terminal) with red handset lead;

Other connections:

WH lead from handset: Network terminal GN;

GN lead from switchook: Network terminal L1 with green line cord lead and black ringer lead;

YL and SL leads from switchook: Network terminal L2 with red line cord lead and red ringer lead.

SL lead from ringer coil: Network terminal K;

SL/RD lead from ringer coil: Network terminal A

***Insulate and store the following dial leads separately***

GN/WH
VI
OR


Ed Vaughn, MBSWWYPBX
Joined: Feb 2005
Posts: 12,332
Likes: 3
Member
***
Offline
Member
***
Joined: Feb 2005
Posts: 12,332
Likes: 3
Have you got the polarity correct?

-Hal


CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
Joined: Jun 2004
Posts: 399
Member
Offline
Member
Joined: Jun 2004
Posts: 399
Sorry to confuse the issue, but I do have the BSP pages for the 2500M / 2500MM / 2500MMG and they differ from what Ed posted. I can PM or post a 6 page PDF, but basicilly I show the following for the 2500MM:

Dial leads:

OR/BK: Network terminal C with white switchook lead;

G: Network terminal F with ringer B and green line cord lead ;

BK: Network terminal RR;

RD/GN: Network terminal R with black switchook lead and handset W;

W: Network terminal GN;

BL: Network terminal B with black handset lead;

WH/BL: Network terminal S (or any blind terminal) with green handset lead and red switchook lead;

RD: Network terminal T (or any blind terminal) with red handset lead;

Other connections:


GN lead from switchook: Network terminal A with red line cord lead;

YL lead from switchook: Network terminal G with yellow line cord lead.

BR lead from switchook: Network terminal L1 with black line cord lead.

RD lead from ringer coil: Network terminal K;


***Insulate and store the following dial leads separately*** (Wires not shown on my print)

GN/WH
VI
OR

Note that the White and Blue Line cord leads were optional connections to the ringer and normally taped off.

PDF file available at:

https://www.jknichols.net/db5/00440/jknichols.net/_uimages/2500M.pdf

Joined: Jan 2005
Posts: 15,335
Likes: 8
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,335
Likes: 8
That is not a problem at all and you certainly are not confusing the issue. I was just recalling the -DM equivalent (non-A lead) wiring from memory. Thanks for posting the real stuff.

By the way, I suspect that the dial was replaced at some point with a speakerphone-compatible one and the spare switching leads were just insulated and stored. I'm sure that's why they didn't show up in your diagram.


Ed Vaughn, MBSWWYPBX
Joined: Jun 2004
Posts: 399
Member
Offline
Member
Joined: Jun 2004
Posts: 399
Also, the 2500MM originally had a type 35 dial that WAS polarity sensitive, but could be upgraded to a 2500MMG with a type 71 dial that did not care about polarity - can you find a code number on the dial with either 35 or 71 in it?

Correct me if I'm wrong, but I think that the Red (ring) wire should be negative 48 volt relative to ground and the Green (tip) wire should be close to Ground

Joined: Feb 2005
Posts: 12,332
Likes: 3
Member
***
Offline
Member
***
Joined: Feb 2005
Posts: 12,332
Likes: 3
That's correct but the easy way to check is to just reverse them (T&R).

-Hal


CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
Joined: Nov 2004
Posts: 290
TDS Offline
Member
Offline
Member
Joined: Nov 2004
Posts: 290

Joined: Dec 2008
Posts: 510
Member
Offline
Member
Joined: Dec 2008
Posts: 510
Several years ago we used a "polarity guard" on a customer's 2500 set that was plugged into an extension port on a Picazo system.


Bob

With all the variables involved, I am amazed when any voice and data technology works like it is supposed to.
Page 1 of 2 1 2

Moderated by  Touch Tone Tommy 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,686
Posts636,173
Members49,606
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
Baron-B, Breneer, dingaling, EV607797, Jase, MED, Mike Robertson, MILLBAX, RANJAN, RootExposure, Tman66
Newest Members
Uranium-235, grahamw, Motel6Guy, JustAGuy, Dialtony
49,606 Registered Users
Top Posters(30 Days)
Toner 12
Yoda 9
dexman 7
Who's Online Now
3 members (dagwoodsystems, metelcom, nortelvoip), 34 guests, and 17 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems & VoIP | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2022
Powered by UBB.threads™ PHP Forum Software 7.7.5