web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
System is CS-5200. At least weekly, and almost daily, the system crashes, with no inbound/outbound calls accepted, system admin handset reads "Sys Alarm #112 - Call Technician". A physical reboot and system OK again, though it appears to be recurring with greater frequency. Some sections of pertinent log files below. Any assistance is greatly appreciated. Just found this resource online, looking forward to using it in the future. Thanks! > ----- START OF RESET LOG ----- > > 12:51 08-08 MAJOR RESET: Database Restore Complete > 12:50 08-08 MAJOR RESET: Code Change > 02:11 08-08 MAJOR RESET: Power-Up > 12:06 08-07 MAJOR RESET: Power-Up > 11:50 08-06 MAJOR RESET: Major Reset From Software Watchdog Thread > 11:38 08-05 MAJOR RESET: Power-Up > 03:09 08-05 MAJOR RESET: Power-Up > 16:56 08-04 MAJOR RESET: Power-Up > 12:38 08-03 MAJOR RESET: Database Restore Complete > 12:37 08-03 MAJOR RESET: Code Change > 16:33 07-29 MAJOR RESET: Power-Up > 09:57 07-27 MAJOR RESET: Power-Up > 20:31 07-26 MAJOR RESET: Power-Up > 18:19 07-24 MAJOR RESET: Reset Due to User Requested Reboot > 07:53 07-15 MAJOR RESET: Reset Due to User Requested Reboot > 23:17 07-10 MAJOR RESET: Power-Up > 14:38 07-09 MAJOR RESET: Database Restore Complete > 14:36 07-09 MAJOR RESET: Code Change > 14:34 07-09 MAJOR RESET: Power-Up > 09:29 07-07 MAJOR RESET: Power-Up > 10:06 07-05 MAJOR RESET: Database Restore Complete > 10:04 07-05 MAJOR RESET: Code Change -01:206- 12:52 08-08 M2002 INF HW CP [3.4.0]: On-Line From Loopstart Port -01:207- 12:52 08-08 M3008 INF EG SS [1.0.0]: Print String Response From PRI Board : T1/E1/PRI application version: 2.1.4 -01:208- 12:52 08-08 M3008 INF EG SS [1.0.0]: Print String Response From PRI Board : T1/E1/PRI application build date/time: Fri Sep 29 2006 12:53:58 -01:209- 12:52 08-08 M8000 SVR HW CP Initial Trouble Condition Detected on PRI Board [1.0.0] -01:210- 12:52 08-08 M8001 SVR HW CP PRI Board Problem: Receiving Yellow Alarm -01:211- 12:52 08-08 M5086 WRN HW CP Hourly Threshold For Bipolar Violation Errors Exceeded on PRI Board [1.0.0] -01:212- 12:52 08-08 M5086 WRN HW CP Hourly Threshold For Out-of-Frame Adjustment Errors Exceeded on PRI Board [1.0.0] -01:213- 12:52 08-08 M5086 WRN HW CP Daily Threshold For Out-of-Frame Adjustment Errors Exceeded on PRI Board [1.0.0] -01:214- 12:52 08-08 M8002 SVR HW CP Initial Trouble Condition Cleared on PRI Board [1.0.0] -01:215- 12:52 08-08 *** PRI Card 1 state changed from Powerup-Wait to Working

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
Ouch, and sorry for the formatting. [code]> ----- START OF RESET LOG ----- > > 12:51 08-08 MAJOR RESET: Database Restore Complete > 12:50 08-08 MAJOR RESET: Code Change > 02:11 08-08 MAJOR RESET: Power-Up > 12:06 08-07 MAJOR RESET: Power-Up > 11:50 08-06 MAJOR RESET: Major Reset From Software Watchdog Thread > 11:38 08-05 MAJOR RESET: Power-Up > 03:09 08-05 MAJOR RESET: Power-Up > 16:56 08-04 MAJOR RESET: Power-Up > 12:38 08-03 MAJOR RESET: Database Restore Complete > 12:37 08-03 MAJOR RESET: Code Change > 16:33 07-29 MAJOR RESET: Power-Up > 09:57 07-27 MAJOR RESET: Power-Up > 20:31 07-26 MAJOR RESET: Power-Up > 18:19 07-24 MAJOR RESET: Reset Due to User Requested Reboot > 07:53 07-15 MAJOR RESET: Reset Due to User Requested Reboot > 23:17 07-10 MAJOR RESET: Power-Up > 14:38 07-09 MAJOR RESET: Database Restore Complete > 14:36 07-09 MAJOR RESET: Code Change > 14:34 07-09 MAJOR RESET: Power-Up > 09:29 07-07 MAJOR RESET: Power-Up > 10:06 07-05 MAJOR RESET: Database Restore Complete > 10:04 07-05 MAJOR RESET: Code Change -01:206- 12:52 08-08 M2002 INF HW CP [3.4.0]: On-Line From Loopstart Port -01:207- 12:52 08-08 M3008 INF EG SS [1.0.0]: Print String Response From PRI Board : T1/E1/PRI application version: 2.1.4 -01:208- 12:52 08-08 M3008 INF EG SS [1.0.0]: Print String Response From PRI Board : T1/E1/PRI application build date/time: Fri Sep 29 2006 12:53:58 -01:209- 12:52 08-08 M8000 SVR HW CP Initial Trouble Condition Detected on PRI Board [1.0.0] -01:210- 12:52 08-08 M8001 SVR HW CP PRI Board Problem: Receiving Yellow Alarm -01:211- 12:52 08-08 M5086 WRN HW CP Hourly Threshold For Bipolar Violation Errors Exceeded on PRI Board [1.0.0] -01:212- 12:52 08-08 M5086 WRN HW CP Hourly Threshold For Out-of-Frame Adjustment Errors Exceeded on PRI Board [1.0.0] -01:213- 12:52 08-08 M5086 WRN HW CP Daily Threshold For Out-of-Frame Adjustment Errors Exceeded on PRI Board [1.0.0] -01:214- 12:52 08-08 M8002 SVR HW CP Initial Trouble Condition Cleared on PRI Board [1.0.0] -01:215- 12:52 08-08 *** PRI Card 1 state changed from Powerup-Wait to Working [/code]

Joined: May 2009
Posts: 1,198
Member
*****
Offline
Member
*****
Joined: May 2009
Posts: 1,198
Alarm 112 indicates the system is running low on System Dynamic Memory. Contact your dealer for assistance.

Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
I have contacted our dealer for assistance, though he wants to replace the whole phone system. I'm looking for an outside opinion.

There is only one other authorized dealer in the area, and we had a bad experience with them.


Joined: May 2002
Posts: 4,295
Likes: 7
Moderator-Avaya, Polycom
*****
Offline
Moderator-Avaya, Polycom
*****
Joined: May 2002
Posts: 4,295
Likes: 7
Where are you located, someone from here may be near by.

Joined: Jun 2010
Posts: 797
Moderator-Inter-Tel
*****
Offline
Moderator-Inter-Tel
*****
Joined: Jun 2010
Posts: 797
Your system is exhibiting a known issue with some PM-1 modules. I would recommend swapping it out first and foremost.

Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
Thanks. If I tell my local dealer I want to try replacing the "PM-1 module", he should know what I'm talking about, correct? Appreciate the guidance guys. -Jimmy

Joined: Jun 2010
Posts: 797
Moderator-Inter-Tel
*****
Offline
Moderator-Inter-Tel
*****
Joined: Jun 2010
Posts: 797
He/She definitely "should".

Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
Thanks. I have an email in to him. In the meantime, we have had to reboot the system twice this morning. I checked our gateway/firewall logs and I see numerous attacks. The alarm we receive - 112 - indicates the log needs to be cleared. Any thoughts? My local service provider here continues to tell me he thinks it's hardware and that these attacks are probably not related, but I think I may need a second opinion. [img]https://www.newsouthsupply.com/files/attach.png[/img]

Joined: Aug 2012
Posts: 9
Member
Offline
Member
Joined: Aug 2012
Posts: 9
Hmmm... Ours started dong that after we connected to a leased line (for lots of external 'remote' users). We spent a good while with the provider suggesting hardware until they finally got an Intertel Expert to look at it who got us to change our firewall rules.. now it doesn't happen. We have forwarded to Mitel. MGCP port 2427 OAI port 4000 Call control 5566 and 5567 Voice 6000-8000 UDP Your ports may differ - check with your provider. I cured my problem. -Smon


If a job is worth doing, it is worth doing well.
Joined: Aug 2012
Posts: 6
Member
*
OP Offline
Member
*
Joined: Aug 2012
Posts: 6
That is very similar to the firewall ports we have open, though on the image I sent yesterday, they were hammering 5566 with a syn flood. Will wait to see if it happens again, and try to confirm that this is indeed the issue. May need to look into IDP devices to put in front of that router.

Joined: Jun 2010
Posts: 797
Moderator-Inter-Tel
*****
Offline
Moderator-Inter-Tel
*****
Joined: Jun 2010
Posts: 797
Try disabling the SIP UDP Listening Port as well. You will also want to change the port to something other than the default of 5060.

Here is a link to a post that discusses it a little more

https://sundance-communications.com...Re_Inter_Tel_system_shutsdown_#Post65299

Joined: Aug 2012
Posts: 9
Member
Offline
Member
Joined: Aug 2012
Posts: 9
I second that; my Mitel BOD was very specific about 5060 - he said never open that on our system!!! Because we do not need it and it is a target for attack by 'free calls on SIP' scroungers.

- Simon


If a job is worth doing, it is worth doing well.
Page 1 of 2 1 2

Moderated by  Stix1 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,696
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,710 CTX100 install
186,795 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 11
TDKs79 8
pvj 4
jc2it 4
Who's Online Now
1 members (justbill), 211 guests, and 241 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5