|
Joined: Aug 2003
Posts: 268
Member
|
OP
Member
Joined: Aug 2003
Posts: 268 |
I have a customer that would like to add a Valcom 2006A for Zone Paging. The MICS has a DTI Card for lines, a 6 port fiber card connected to a 0X16 and an ASM. I tried a V9970 off an analog station but it does not pass DTMF necessary to get the zones. It appears I need to add a Trunk Card. First, if I add a trunk card, can it go into Slot 3 or do I need to add a TM as well? Second, is this plug and play, with the first line on the LS/DS becoming line 025?
Mike
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
There is an external page port/contact on all Norstar KSU's. To page use Feature 60 and choose Sets or Speakers or Both. To page only Speakers (external page port) use Feature 62 then enter zone #.
|
|
|
|
Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
|
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086 |
There is an external page port/contact on all Norstar KSU's...........To page only Speakers (external page port) use Feature 62 then enter zone #. That of course is wrong info. For external ZONE paging you do need to use a trunk port. I would assume your DRI is in the right slot. The DS Trunk card goes just left of that. With 6.1 the first trunk is 31. Not 100% plug & play but close.
Last edited by NTlayoff; 02/22/14 01:24 PM.
If CON is the opposite of PRO Then what is the opposite of Progress?
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
"That of course is wrong info."
One What is with the attitude? did I piss you off some how?
Two How is it the wrong info? please explain in full detail.
Thanks
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
I think I get it, Valcom does not integrate well with Norstar like Bogen, Tortech and so on so no choice but to use a line port with Valcom systems?.
Thanks
Last edited by Curlycord; 02/22/14 02:26 PM.
|
|
|
|
Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
|
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086 |
..........What is with the attitude? did I piss you off some how?.......How is it the wrong info? please explain in full detail. Naw - you did not "piss me off". You are always QUICK to reply. Most of the time you have good input. But I think you reply too fast before thinking and there is usually one little part that is not correct. Sorry - I did not mean it that way. You said, To page only Speakers (external page port) use Feature 62 then enter zone #. The little part that is not correct is that after F62 you can't enter zone #. Zone paging is only for Set paging or external using a Trunk.
If CON is the opposite of PRO Then what is the opposite of Progress?
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
The poster has indicated he has 6.1, this means DTMF tones are passed through the page port. Manufacturers such as Bogen or Tortech allow for Tip and Ring paging from Norstar page ports. Zone paging thus can be accomplished on overhead speakers.
Page port cross-connects to the Tip and Ring on a Zone Module.
F62 to open the port (page request) Enter the digits required by your zone module (zone request).
"You are always QUICK to reply.
But I think you reply too fast before thinking and there is usually one little part that is not correct."
Not everyone is as young and not forgetful or as sharp as you might be. Your comments are not welcomed nor were they warranted in the least..
Last edited by Curlycord; 02/22/14 03:28 PM.
|
|
|
|
Joined: Sep 2005
Posts: 9,285 Likes: 6
Admin
|
Admin
Joined: Sep 2005
Posts: 9,285 Likes: 6 |
Lets calm this down. Both of you have and give lots of good advice. There are many differences in systems and external equipment so not everyone does things the same way. If you have advice for the OP then please post but there is no need to negative replys if someone else does things differently. With people from different areas and countrys posts can be read wrong and/or misunderstood also equipment may vary.
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
|
|
|
|
Joined: Jan 2002
Posts: 2,328
Moderator-Comdial
|
Moderator-Comdial
Joined: Jan 2002
Posts: 2,328 |
I have a customer that would like to add a Valcom 2006A for Zone Paging. The MICS has a DTI Card for lines, a 6 port fiber card connected to a 0X16 and an ASM. I tried a V9970 off an analog station but it does not pass DTMF necessary to get the zones. It appears I need to add a Trunk Card. First, if I add a trunk card, can it go into Slot 3 or do I need to add a TM as well? Second, is this plug and play, with the first line on the LS/DS becoming line 025?
Mike Set a customer with PRI up like this a year ago. They originally had a V2001 but wanted more zones so I installed a V2006. I put the trunk into its own line group and programmed that button on each phone. Occasionally they forget to hangup after a page and neither the Valcom nor the Nortel has a time out disconnect. I wrote up a line/trunk disable procedure and trained the two operators. Haven't been back because paging is locked up! The IP Flex from At&T is another story.
|
|
|
Forums84
Topics94,284
Posts638,772
Members49,765
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
142
guests, and
285
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|