web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#570443 04/18/14 10:52 AM
Joined: Nov 2001
Posts: 461
Likes: 1
teleco Offline OP
Member
OP Offline
Member
Joined: Nov 2001
Posts: 461
Likes: 1
I'm having trouble with loop start lines not releasing. I am getting a disconnect signal, I am using a Time Warner cable modem for the lines.The lines do actually disconnect,but the LED stays red and can not be used. If I pull the bridge clips off, then access the lines, they will release, if the lines are showing busy and I pull the amphenol off the card, they still show busy. No alarms, can't manually release them from the console. I've programmed them for supervised and unsupervised with no change. Any suggestions? Thanks

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Oct 2004
Posts: 1,057
Member
****
Offline
Member
****
Joined: Oct 2004
Posts: 1,057
If the LED stays lit, after pulling of the amp cable, I'd suggest replacing the trunk card.


www.ResaleSystems.com 24 x 7 Mitel Parts and Free Tech Support
Joined: Nov 2001
Posts: 461
Likes: 1
teleco Offline OP
Member
OP Offline
Member
Joined: Nov 2001
Posts: 461
Likes: 1
Replaced trunk card, no change. T&R were reversed, also grounded KSU to cable modem, and problem cleared. The thing that still gets me is the other day when the trunks did not releasing after I pulled the amp conn. from the card. Thanks

Joined: Feb 2006
Posts: 1,716
Member
***
Offline
Member
***
Joined: Feb 2006
Posts: 1,716
Methinks Sum Ting Wong. Grounding the PBX should be to the building ground which should be bonded to ALL telephone equipment including the modem. Just grounding the modem to the PBX would have no effect on loop start trunks. There is no reference point on loop start to ground as the loop IS the circuit. If this were Open Tip (Ground Start) then I could see a possibility.

I think you need to check programming and make sure the trunks are setup for loop start.

Rcaman


Americom, Inc.
Where The Art And Science Of Communications Meet
Joined: Nov 2001
Posts: 461
Likes: 1
teleco Offline OP
Member
OP Offline
Member
Joined: Nov 2001
Posts: 461
Likes: 1
Rcaman what I did fixed the problem. Somting not wong anymore, as I stated in my post.


Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,697
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,712 CTX100 install
186,796 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 11
TDKs79 8
jc2it 4
teleco 4
Who's Online Now
1 members (Toner), 116 guests, and 244 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5