Previous Thread
Next Thread
Print Thread
Rate This Thread
#608256 - 02/24/17 04:23 PM Should messenger strands be grounded for lightning protection?  
Joined: Aug 2016
Posts: 18
Bruno Offline
Member
Bruno  Offline
Member

Joined: Aug 2016
Posts: 18
Canada
Hello all,

I have hundreds of feet of copper wire lashed to 1/8" steel messenger strand running through poles and trees. This is a private plant on a forested land and there is usually no primary or secondary power lines above the comm space.

We often have lightning strikes on trees. I have seen lightning jump from one tree to another via a steel cable before (killed both trees).

I have put protection on phone cables entering buildings but I am wondering if I should ground the strand so that lightning is diverted to ground rods instead of following phone cables. And if so, at what intervals should I put ground rods.

Does that make sense? What is the practice? I haven't seen this mentioned in RUS bulletins.

TIA

Google Telephone Equipment Search
#608261 - 02/24/17 05:07 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: May 2002
Posts: 3,559
hitechcomm Offline
Moderator-Avaya, Polycom
hitechcomm  Offline

Moderator-Avaya, Polycom
*****

Joined: May 2002
Posts: 3,559
New York, NY
Bruno, yes you should ground those wires.
Here NYC we don't do that, very little exposed cables.
I'm sure someone will follow who can point you in the right direction.

#608271 - 02/24/17 08:33 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: May 2002
Posts: 16,485
justbill Online content
Admin
justbill  Online Content

Admin
****

Joined: May 2002
Posts: 16,485
Western Nebraska
I found this with a google search. I didn't read it so don't know if it will address your specific issue or not.

Yes the strand should be grounded at each end with #6 copper ground and a 10ft copper ground rod. I don't remember the intervals at which this was done, but I do remember bonding to the power ground, it may have just been where it was available. I really don't recall the B.S.P on this. I kind of recall at one point the practice changed to where we didn't bond to the power ground, but I'm not positive about that. I do remember having "hot" grounds a few times when the ground wire to the ground rod was broken on power poles. We were required to test the ground wire prior to climbing a joint use pole.

Here is my google search if it helps.


Retired phone dude
#608276 - 02/24/17 11:02 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Feb 2006
Posts: 1,718
Rcaman Offline
Moderator-ESI
Rcaman  Offline

Moderator-ESI
***

Joined: Feb 2006
Posts: 1,718
Pittsburgh, PA
The NESC, which is the OSP foreman's Go To reference has specific rules regarding telephone cable strand bonding. Rules 096, 097G, 344, 354, 384C for starters.

The rule of thumb and supported by the NESC is every 1/4 mile the strand must be bonded and grounded. Look Here

Rcaman


Americom, Inc.
Where The Art And Science Of Communications Meet
#608483 - 03/03/17 10:08 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Aug 2016
Posts: 18
Bruno Offline
Member
Bruno  Offline
Member

Joined: Aug 2016
Posts: 18
Canada
Thanks gentlemen for all this helpful information.
I'll get a few ground rods and a jackhammer.

#608527 - 03/05/17 07:04 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Sep 2006
Posts: 3,111
Arthur P. Bloom Offline
Member
Arthur P. Bloom  Offline
Member
*****

Joined: Sep 2006
Posts: 3,111
Shelter Island, New York
You don't need a jackhammer. You can use a hammer drill, with a 1/2" socket wrench extension, plugged into an expendable 1" socket. Put the extension into the chuck of the drill, and put the socket over the end of the ground rod. Set the drill motor to "hammer only" and voila.

When the rod is almost at the correct depth, fasten the ground wire and clamp to the rod, then pound it the rest of the way, so that the clamp is below grade. This protects it from dog pee, lawn mowers and vandals.


Arthur P. Bloom
"30 years of faithful service...15 years on hold"

#608625 - 03/08/17 04:25 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Aug 2016
Posts: 18
Bruno Offline
Member
Bruno  Offline
Member

Joined: Aug 2016
Posts: 18
Canada
Good idea. Thanks!
Also I've read fence post drivers work well for this, especially useful when no power is available.

#608626 - 03/08/17 04:35 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Feb 2005
Posts: 11,649
hbiss Online content
Member
hbiss  Online Content

Member
***

Joined: Feb 2005
Posts: 11,649
New York
So does a sledge hammer and elbow grease...

-Hal


CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
#608628 - 03/08/17 05:38 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: May 2002
Posts: 16,485
justbill Online content
Admin
justbill  Online Content

Admin
****

Joined: May 2002
Posts: 16,485
Western Nebraska
Using a post driver will work if the ground is not real hard. If it's really hard dry clay or real rocky you'll just bend it. I've used them and they work pretty good. Mostly just a 3 lb hammer and elbow grease as Hal said.


Retired phone dude
#608631 - 03/08/17 08:48 PM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Aug 2016
Posts: 18
Bruno Offline
Member
Bruno  Offline
Member

Joined: Aug 2016
Posts: 18
Canada
Nobody trusts me enough to hold the rod while I wield the hammer.
They must know something that I don't.

#608639 - 03/09/17 12:57 AM Re: Should messenger strands be grounded for lightning protection? [Re: Bruno]  
Joined: Sep 2006
Posts: 3,111
Arthur P. Bloom Offline
Member
Arthur P. Bloom  Offline
Member
*****

Joined: Sep 2006
Posts: 3,111
Shelter Island, New York
"Ollie, when I nod my head, you hit it!"


Arthur P. Bloom
"30 years of faithful service...15 years on hold"


Moderated by  EV607797 

Refurbished Phones & Equipment Search
TARGETED LEADS Telephone Installers, System Installation & Phone System Sales!
Technician Search, enter State or Zip Code
Shout Box
FREE DESI Labeling System Software!
FREE DESI Labeling Software - Click Here!
Most Recent 5 Post
Ring Plan Help
by jrm2002ss. 12/16/17 05:51 PM
SVMI20e Email gateway settings
by Tariq. 12/16/17 07:39 AM
Avaya Emerges From Chapter 11
by reidtel. 12/15/17 10:33 PM
SBX IP 320 - Entering Lowercase in Station Name
by wahsatchmo. 12/15/17 10:18 PM
radio channels on analog ports
by Bushmills. 12/15/17 06:58 PM
Who's Online Now
11 registered members (Mercenary Roadie, Touch Tone Tommy, dexman, RATHER BE FISHING, hbiss, metelcom, jeffmoss26, Silversam, justbill, Professor Shadow, MooreTel), 185 guests, and 499 spiders.
Key: Admin, Global Mod, Mod
Tech Support Line 1.800.766.3425
Over the Phone Tech Support for your Phones and Business Phone Systems
Popular Topics(Views)
Newest Members
Statistikal, wahsatchmo, ShiWham, AdamCook605, shadowstock1
48359 Registered Users
Forum Statistics
Forums60
Topics90,108
Posts614,106
Members48,360
Most Online4,713
Apr 2nd, 2014
Today's Birthdays
Joseph Talbot
Top Posters(30 Days)
dexman 31
John807 15
hbiss 13
dans 12
Free Voip phone with every line!
FREE Voip Phone - Click Here!
Ad Spot for sale $299 This spot gets 5 million page loads per month! Call 1-800-766-3425
Free Phone Repair Diagnostic
Website for sale!
Business and website or sale!
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2017
Website Malware Scan




Trusted Partners
Sitemap