Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Vodavi stse
#633049 09/30/19 04:29 PM
Joined: Apr 2009
Posts: 379
Gary S. Offline OP
Member
OP Offline
Member
Joined: Apr 2009
Posts: 379
On site this am. The "I hold" device is bleeding over to the 24v paging horns at a low volune. The i hold puts caller on hold after 4 rings with music and message, then gives a
announcement call holding on line x. You can faintly here mucic and dtmf over the horns. the ksu was replace about 2 years ago. Another mom and pop business that
would rather repair then replace..Thanks for any help!
Gary S.


Gary Stevens
EMP & Lightning Home Surge Protection
EMP - Click Here!
Re: Vodavi stse
Gary S. #633177 10/08/19 01:19 AM
Joined: Feb 2009
Posts: 3,125
Moderator-Vodavi, Vertical, XBlue
*****
Offline
Moderator-Vodavi, Vertical, XBlue
*****
Joined: Feb 2009
Posts: 3,125
When a system has MOH turned on but without a source such as your I-Hold, it is sometimes possible for audio to bleed over from other sources. But since that is not your case and if you can't go the replacement route, the best thing I can think of is to turn the volume down as low as possible on the I-Hold and hope for the best. The only other thought is get some ferrite cores and wrap the CO cross-connect through them 5-7X. Ferrite cores came with their older systems for use on the CO line cords but we never used them unless we had RF interference.


- Dave S. -

You can never appease your ideologue opponents.

Re: Vodavi stse
MnDave #633185 10/08/19 01:20 PM
Joined: Apr 2009
Posts: 379
Gary S. Offline OP
Member
OP Offline
Member
Joined: Apr 2009
Posts: 379
Dave. Thanks for your reply. I was thinking also about a bleed over but this i hold was put in Aug 2018 and just started with this trouble a few weeks ago ??
Thanks gary S.


Gary Stevens
Re: Vodavi stse
Gary S. #633222 10/11/19 04:29 AM
Joined: Feb 2009
Posts: 3,125
Moderator-Vodavi, Vertical, XBlue
*****
Offline
Moderator-Vodavi, Vertical, XBlue
*****
Joined: Feb 2009
Posts: 3,125
Gary. Since you have the ihold that auto answers, that means you are not using the KSU MOH input. So make sure that MOH is disabled in Flash 05 Button 12. I really don't know how the RF is getting into the Page port, but this is something that you can check off the list. Also check the line voltage and the loop current coming out of the ihold. If it is running too hot weird stuff can happen.


- Dave S. -

You can never appease your ideologue opponents.


Link Copied to Clipboard
Forum Search
Most Recent 5 Post
2199 Lithium battery
by brokeda - 10/24/20 06:01 PM
Colour Choice for X-16 gone...
by MooreTel - 10/24/20 01:49 AM
Are you an Asterisk Ace?
by Toner - 10/22/20 03:39 PM
SVMI Card settings backup & restore
by Hofman telekom - 10/21/20 01:46 PM
Who's Online Now
20 members (newtecky, justbill, Joe Talbot, Mercenary Roadie, Bob3470, hitechcomm, Yoda, RATHER BE FISHING, Herk, jsb15, nfcphoneman, nortelvoip, Edward_, buttercool, BobRobert, hbiss, Curlycord, brokeda, dexman, Touch Tone Tommy), 126 guests, and 128 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums94
Topics94,026
Posts637,641
Members49,367
Most Online5,661
May 23rd, 2018
Today's Birthdays
There are no members with birthdays on this day.
Newest Members
chelsea419, jsb15, C.t.c.73, Farquie, 4teltech
49367 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
Top Posters (30 Days)
dexman 20
Ruben 15
hbiss 12
Toner 9
Bluewater Sailing
https://www.patreon.com/bePatron?u=5256033
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Sold AD
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2020
Trusted Partners