Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Stupid Paging Question - Replaced Partner with IPO
#637172 06/18/20 01:43 PM
Joined: Feb 2007
Posts: 2
Member
OP Offline
Member
Joined: Feb 2007
Posts: 2
I replaced a Partner ACS using a Page Pac D20 with an IP Office. What is the best way to determine if the Page Pac 20 was set to line or station port? There is/was a cord going from the Page In port on the Page Pac to the paging port on the Partner. I can't find any documentation that says whether it is line or station port - I thought I programmed it for both but neither works. Want to verify which it should be before going back to site. Or are they even compatible? Thank you in advance.

Last edited by secondshift; 06/18/20 01:49 PM.
Bluewater Sailing
https://www.patreon.com/bePatron?u=5256033
Re: Stupid Paging Question - Replaced Partner with IPO
secondshift #637176 06/18/20 06:36 PM
Joined: Jul 2001
Posts: 3,278
Moderator-Avaya-Lucent, Antique Tele
*****
Online Content
Moderator-Avaya-Lucent, Antique Tele
*****
Joined: Jul 2001
Posts: 3,278
Partner ACS paging port has audio on the center pair, and a contact closure when paging on the pair surrounding the center pair. On the Page Pac 20, you would connect a 4 conductor line cord and set the slide switch to Page port.

On IP Office, the best way is to use a single-line station port, set the Equipment Classification on the Ananlogue Options tab to Page Port, and use a Viking AIB-1 Audio Isolation Transformer between the IPO and the paging amplifier. You can use the same input jack or the screw terminals on the amp instead. Still put the slide switch to Page Port, and if the amp is not VOX activated, place a short from Ground to C1,

If you want to use an Analog Trunk Port on the IP Office, set the slide switch to Loop Start.

Analog trunk port programmed as a page port allows simultaneous paging, which the trunk port does not.


Link Copied to Clipboard
Forum Search
Most Recent 5 Post
Are you an Asterisk Ace?
by Toner - 10/22/20 03:39 PM
SVMI Card settings backup & restore
by Hofman telekom - 10/21/20 01:46 PM
IPOffice remote voice mail access
by Brian A - 10/21/20 11:41 AM
Also looking for Crossbar PBX
by Joe Talbot - 10/21/20 08:40 AM
You'll LOVE this... Looking for Dimension tapes
by Joe Talbot - 10/21/20 08:34 AM
Who's Online Now
31 members (metelcom, Carl Navarro, Curlycord, Toner, sfletcher, Daniel, ToshiGal75, Bushmills, NateBates, dexman, Touch Tone Tommy, chelsea419, Roscoe, Iwatsu Guru, Professor Shadow, jsb15, KRRath, nwilliams, DD782, Ruben, jsaad, Hofman telekom, Edward_, jknichols, mongo5150, Joe Talbot, MooreTel, Brian A, Skunky, nameless, ssdr9163), 473 guests, and 67 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums94
Topics94,022
Posts637,605
Members49,367
Most Online5,661
May 23rd, 2018
Today's Birthdays
DSIDAVE, Tom Lynden
Newest Members
jsb15, C.t.c.73, Farquie, 4teltech, TRIM IT
49366 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
dexman 23
Ruben 15
hbiss 12
Daniel 10
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Sold AD
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2020
Trusted Partners