|
Joined: Oct 2011
Posts: 4
Member
|
OP
Member
Joined: Oct 2011
Posts: 4 |
Hello Everyone, New to the forum, and hope to get some help please. Purchased an Axxess system for my home/office, and would like to get it working....I have KSU/Limited phone system experience (I am an electronic tech, mainly CCTV/Card Access Systems/intercoms, etc.).
I powered up the KSU and when I hooked up the a phone, it had the system dialtone. I connected my COs to the LSC card and couldn't dial an outside call...display said TS 9*** was unplugged?? I then turned the system off and swapped out the LSC with a LSG card I had and connected my CO's...then the power supply popped, no lights, no power, only a relay sound.
I had another power supply I purchased (they are both the 550-0110 9amp models), so I installed it and yup...the same thing. What is so sensitive about these power supplies that makes them pop so easy? All I want is to initiate my 4 lines on my 14 phones....any suggestions?
I have 2 KSU's with many cards.....just tell me what cards I need for the 2 executive phones, 12 standard display phones, 4 CO lines (voip,thru router) that I need please.....This is a feature-rich, complex system, and even though I plan on using many features, I would be happy to just get the basics operating for now. Sorry this is so long, wanted it to be as detailed as possible. Thanks! Mark
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jun 2010
Posts: 797
Moderator-Inter-Tel
|
Moderator-Inter-Tel
Joined: Jun 2010
Posts: 797 |
Welcome to the forum nightwalks!
Those power supplies do go bad from time to time. Yours could have been dead or about to blow before you even received them. I'm assuming you're just plugging them into a standard 110 outlet.
The cards you'll need are:
Power Supply
DKSC16+/DKSC16/DKSC - any of these will work although your best bet would be DKSC16+. This card will provide up to 16 digital circuits. The DKSC only provides 8 digital circuits so you would need 2 if you go this route to accommodate your 14 phones.
LSC - accommodates 4 loop start lines.
CPU or CPC depending on what came with the system. This is the processor card.
Unsure what the LSG card you had is. There is an LGC card which would accommodate either loop start or ground start trunks depending on what you have and how it's programmed.
Once those cards are in place and powered on, you would need to get access to the Session Manager software and more than likely an Axxess connector in order to program the system up. You'll also have to hope the CPU/CPC doesn't have a password on it.
In all honesty, your best bet would be to contact a tech that can come in and get you all situated. It shouldn't take that long at all for what you need.
|
|
|
|
Joined: Oct 2011
Posts: 4
Member
|
OP
Member
Joined: Oct 2011
Posts: 4 |
Thanks so much for your response...yeah, I meant to state I had the LGC card---I have VOIP CO lines...not direct, they are through the router and provide direct dial-tone...do you know if these are considered loop or ground start in nature? I would think loop?
I found 2 blown transistors in the power supply, they are ordered as we speak. Just seemed funny when I plugged in, connected and powered up that LGC card it blew. Do these cards need to be in specific/programmed locations or can they be shuffled around at random?
I have all the manuals and a few CDs that came with the system, but not sure what I need to start programming (I am familiar with programming my CCTV and elevator systems, so Id like to try this system). I did get a serial looking cable with the system, but I think that's for the network/T1 cards that are in the KSU?
What cable do I need and does it connect directly to the CPU? Session Manager is where, in the CPU or the CDs I have? And I assume the password can be overridden by resetting something?
Here is what I have: I purchased the 15 phones with a KSU that has: 2- DKSC16, SLC, OPC, IPRC, T1C, CPU 128S and of course the power supply.
I bought a second KSU for the power supply (before I realized I could fix it), it has: 2-DKSC, DKSC16, LSC, LSC, OPC, CPU. I also bought the LGC card thinking I may need it.
SOOOO, there is my system....any further help you could give is greatly appreciated. As I said, I have always worked on phone systems in my earlier days, but got more involved in the CCTV and access controls and elevator electronics as of late, so I am out of touch on these higher-level programmable systems. Thanks again! Mark
|
|
|
|
Joined: Jun 2010
Posts: 797
Moderator-Inter-Tel
|
Moderator-Inter-Tel
Joined: Jun 2010
Posts: 797 |
Here is how I would configure the system. Slot 1 - DKSC16 Slot 4 - LSC Slot 7 - OPC Slot 8 - CPU or CPU128S Not sure what CD's you have but you are looking for the DB Programming software. Once you run the executable, the programming software is called Session Manager. You will need the proper version to connect to either the CPU or CPU 128S. For example, if you have version 6 of DB Programming, it will not connect to a CPU that is version 7. Also, here is a link that will explain the type of connector and cable you need to connect to DB Programming. https://www.sundance-communications.com/cgi-bin/ultimatebb.cgi?/ubb/get_topic/f/4/t/000587.html
|
|
|
|
Joined: Dec 2002
Posts: 9,423 Likes: 1
Member
|
Member
Joined: Dec 2002
Posts: 9,423 Likes: 1 |
To find the version, you can connect the cable to your computer and the CPU card, fire up hyperterminal, and power up the system and it should show you what version the software is.
Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE
|
|
|
|
Joined: Oct 2011
Posts: 4
Member
|
OP
Member
Joined: Oct 2011
Posts: 4 |
Thanks guys, Ill give it a shot as soon as I get the power supply transistors in...Ill keep you updated... M
|
|
|
|
Joined: Dec 2002
Posts: 9,423 Likes: 1
Member
|
Member
Joined: Dec 2002
Posts: 9,423 Likes: 1 |
I will also say that the programming is not exactly user-friendly. Just a heads-up.
Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE
|
|
|
|
Joined: May 2009
Posts: 1,198
Member
|
Member
Joined: May 2009
Posts: 1,198 |
User friendly? Probably not.
Technician friendly? I’ve seen worse.
|
|
|
|
Joined: Dec 2002
Posts: 9,423 Likes: 1
Member
|
Member
Joined: Dec 2002
Posts: 9,423 Likes: 1 |
Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE
|
|
|
|
Joined: Oct 2011
Posts: 4
Member
|
OP
Member
Joined: Oct 2011
Posts: 4 |
Oh I expect it's going to be proprietary and difficult....
|
|
|
Forums84
Topics94,284
Posts638,768
Members49,765
|
Most Online5,661 May 23rd, 2018
|
|
1 members (James D.),
133
guests, and
311
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|