|
Joined: Mar 2002
Posts: 3,630
Moderator-Avaya, Nortel
|
OP
Moderator-Avaya, Nortel
Joined: Mar 2002
Posts: 3,630 |
i have a customer who is going to change out there service today from IFBs to two PRI circuits. I assume I build each PRI as a seperate circuit, with their own b-channel groups and all, and then just assign them as say 70 pool for PRI # 1 and 890 Pool for PRI #2? Then build the ARS tables accordingly?
|
|
|
|
Joined: May 2004
Posts: 1,663 Likes: 4
Moderator-Avaya
|
Moderator-Avaya
Joined: May 2004
Posts: 1,663 Likes: 4 |
Switch must be on Hybrid Mode
1. Set Frame Format to Extended Super Frame Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Frame Format=>Extended Super Frame=>Enter.
2. Set Suppression Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Suppression=>B8ZS=>Enter.
3. Change Type to PRI. Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Type=>PRI=>Enter.
PRI MENU
4. Set Switch Type. Lines Trunks=>PRI=>Switch Type=>make choice+Enter.
5. Program B-Channel Group. B-Channel Group=>B-Channel=>When prompted for b-channel group, type 1+ Enter. When prompted for B-Channels, enter in the form: slot/B-Channel(sspp) starting with B-Channel 23 and working down to B-Channel 1. Example: if slot is 4, type 0423, enter, 0422, enter, 0421, enter, ect……….0401. Return to B-Channel Group menu.
6. Program Lines. Lines=> when prompted for b-channel group, type 1 + Enter=>enter line trunks (1st 23 only). Return to B-Channel Group menu.
7. Set Network Service. Ntwk Svc=>Misc=>CallByCall=>Enter. Return to B-Channel Group menu.
8. Set Incoming Routing. Incoming Rtg=>Dial Plan=>Enter. Return to B-Channel Group menu.
Back
9. Program Dial Plan Routing. Dial PlanRouting=>Service=>0=>Misc=>Any=>Enter. Exit back through Dial Plan Rtg menu to PRI menu.
Back
10. Program Outgoing Table. Outgoing Table=>CBC Svc=>Pattern=>when prompted for list and entry numbers, enter 00=>Enter. When prompted for pattern number, enter: 0=>Next(F9)=>1=>Next=>2=>Next……..8=>Next=>9=>Enter.
Back
11. Set Network Service. Ntwk Svc=>Misc=>No=>Enter.
If this is a general use PRI, you must change the Special Service Table as follows: PRI=>Outgoing Table=>Special Svc=>Del Digit=>When prompted for entry number, enter 0 + Enter. Change entry to 0=>Next=>change entry to 0=>Next, ect until all entrys, 0-7 are 0.
If this is a strictly long-distance PRI, leave the Del Digit values at default.
INFO for PRI Provider
- PRI ESF B8ZS - The Terminal Equipment Identifier (TEI) = 0 - Switch Type: 5ESS - Optioned for "Custom"
If switch type is DMS-100, The protocol MUST be set for “NTNAPRIâ€. Additionally, if the switch type is DMS-100, the field “L1 flags†in the “Trunk Sub Group†table should be set to yes. This is more critical when using DS1 cards with an Apparatus code beginning with “517Mâ€. These particular DS1 boards WILL NOT work properly without this parameter set
|
|
|
|
Joined: Mar 2002
Posts: 3,630
Moderator-Avaya, Nortel
|
OP
Moderator-Avaya, Nortel
Joined: Mar 2002
Posts: 3,630 |
thanks Mongo, I have the setup procedures. My question is concerning TWO PRI circuits handling in and outbound calls for one DID range. Do I just treat them as seperate circuits until the ARS tables.
|
|
|
|
Joined: Apr 2006
Posts: 1
Member
|
Member
Joined: Apr 2006
Posts: 1 |
Yes you are right. 2 pools and then just do the ars overflow from the 70 pool to the 890 pool. better that way anyway. I have several locations with multiple pri's here in vegas.
|
|
|
Forums84
Topics94,284
Posts638,772
Members49,765
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
121
guests, and
316
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|