I have upgraded to the latest software on nec 48. Mifu also upgraded. Phones still only show 10 latest caller id. Any ideas ?
Lane
I think a KMM chip is needed on the MIFM for that.
Thanks Doc.....I do have the kmm (5.0)chip?
Lane
got to have version 8000 or higher to get the 50. per the features & specs manual:
DESCRIPTION
Analog Caller ID can display the calling party name and telephone number on
the LCD of the Multiline Terminal for incoming calls. For normal incoming calls
(Day or Night ring assignment), up to 16 Multiline Display Terminals can
display the Caller ID for the incoming analog trunk. for Direct Inward
Termination (DIT) calls, the Caller ID information is displayed at the
terminating station. After the CO call is answered, the Caller ID information
follows a transferred call.
When the MIFM-U( ) with KMM(1.0)U is installed, the Caller ID information can
be displayed for the last 50 incoming calls by using the Caller ID scroll key
when it is assigned.
The name and number can be displayed at the same time for Analog Trunks
(System Software 4000 or higher).
Fifty Caller ID scroll buffers are provided (System Software S8000 or higher
and MIFM-U( ) Firmware V5.00).
Only 10 Caller ID scroll buffers are provided (System Software S7000 and
below or lower level MIFM-U( ) firmware).
AVAILABILITY
Terminal Type:
All Multiline Terminals with an LCD
Required Components:
COID(4)/(8)-U( ) ETU
COIB(4)/(8)-U( ) ETU
MIFM-U( ) ETU with KMM(1.0)U installed when Caller ID Scrolling or Call
Return is desired.
Data Assignment:
Caller ID Indication (Analog Trunks)
_ Use Memory Block 7-1 (Card Interface Slot Assignment) to specify
COID 4, COID 8, or MIFM.
_ Use Memory Block 1-1-78 (Caller ID Display Assignment for System
Mode) to assign up to 15 Multiline Display Terminals to display Caller
ID indication for incoming calls.
_ Use Memory Block 4-49 (Caller ID Display for CAR Key Assignment)
to assign one Multiline Terminal per CAR Key to display Caller ID
indication for incoming calls.
_ Use Memory Block 3-44 (Caller ID Display Assignment for CO/PBX
Line) to assign the Caller ID Display for normal incoming CO/PBX
calls.
_ Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 4 LK 3 to Allow (LED On) or Deny (default: LED
Off) Caller ID.
_ Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2] Page 4 LK 4 to Allow (LED On) Caller ID Number display
or Deny (default: LED Off) to display the Caller ID Name, when Name
and Number are received.
Hey Chris.......
Thanks for the info. ID has been set up correctly thanks to you from before. I just got updated to 8.71 ver and expected the "50 id scroll" ....still only get 10 so I thought I'd see if you knew of anything else I'm missing?
Thanks Lane
Hey Chris.........
I figured it out.........so just for everyones sake:
After installing the upgrade, you are not done. MIFM-U Firmware chip must also be upgraded to Ver 5.00 in order to get the 50 caller ID's under scroll.
Lane
yeah.....i thought that's what i posted above!
:-)
Fifty Caller ID scroll buffers are provided (System Software S8000 or higher
and MIFM-U( ) Firmware V5.00).
i think the mifm upgrade is about the same as the cabinet (never done a mifm upgrade)
Thanks Chris......
I'll let you know after I get the upgrade how it goes. Bought MIFM card from nec recond. Wouldn't you think the ver would be higher than 1.00!!!!!
Lane
nec is funny like that on their recond. stuff.
but hey! if it's a good deal......
------------------------------------
now if you need a vm update let me know. i can get those 4 free pretty much!