I had this phone system passed on to me as I took a new job, and I am quickly learning a lot about it however I am struggling to figure out an issue. We have a two Cisco RV320 creating a VPN tunnels between offices, and trying to configure the remote phones to hit the local SIP server. I can ping back and forth across the network The Local Cisco Router 10.1.10.1 The Remote Cisco Router is 192.168.3.1 The local SIP server IP address is 10.1.10.112 The remote phone is setup as the following IP 192.168.3.155 Subnet 255.255.255.0 Gateway 192.168.3.1 SIP IP 10.1.10.112 It is getting SIP server not found error Any IDEAS?
A lot. Is this an existing VOIP network or are you just setting it up?
It is a new VPN addition to existing phone system
Are there additional configuration that needs to be made in order for the traffic to travel over the vpn?
Depends on what you have programmed in network setting on the system. Why a VPN vs just doing NAT?
We need the VPN for other purposes, but this decision was put in play before I was actually hired. Is there no advantage to sending the traffic across the VPN?
Depends on what you need the VPN for. VPN's in my experience simply add latency and steal bandwidth. But regardless you need to look at your network config on your phone system. Is the VPN actually working? Is the phone programmed correctly? Have you tested the phone on the local network to make sure it's functioning?
Did you have a remote phone working before you added vpn? If so how two sites were connected before?
Yes the VPN is working I can ping from either side and have even transferred a file across. Phone were connected with a Public IP address as the SIP Server previously, we are trying to use the VPN for security purposes.
Well first question did you turn off NAT on the phones?
I'm very green when it comes to this phone system, no I did not turn it off, it is currently set to Dynamic
Nat transversal needs to be off.
I thought we had this issue resolved. I turned off NAT traversal. Extension to extension calls work fine We can dial and receive calls, but the audio is not being passed across the VPN Setup Local Router 10.1.10.x Site to Site VPN via Cisco RV320 Remote location 192.168.3.x Phones in remote site IP address of 10.1.10.x Gateway is IP address of Router at local site Nat Traversal Disabled Sip Server is Local SIP server 10.1.10.x RTP & Self SIP ports are set to even numbers out of range or conflict Any idea what I am missing?
I see no mention of the IP address for the DSP resource, you will not have audio if one has not been configured.
Does this need to be set on the phone? Extensions were working fine before we put them behind the VPN.
If it was working before the VPN means the DSP resource was setup, see 84-26-01 for IP address Have you contacted Cisco about this issue?
Look in 10-58 to make sure your local network (VPN etc) is defined. It's probably trying to send the packets via NAT like it's been programmed to do. 192.168.0.0 255.255.0.0 etc if you are on a 172.x.x.x or 10,x,x,x these need to be properly defined.
Look in 10-58 to make sure your local network (VPN etc) is defined. It's probably trying to send the packets via NAT like it's been programmed to do. 192.168.0.0 255.255.0.0 etc if you are on a 172.x.x.x or 10,x,x,x these need to be properly defined.
There is nothing defined in 10-58
Just to be clear before I make this change to the PBX programming
in 10-58 I should have
IP address #1
10.1.10.0
255.255.255.0
IP Address #2
192.168.3.0
255.255.255.0
10.1.10.x is my PBX
192.168.3.x is my remote network
?
This basic IP routing 101. The only 3 you need that should cover everything is: 10.0.0.0 sub 255.0.0.0 172.16.0.0 sub 255.240.0.0 192.168.0.0 sub 255.255.0.0
I think you should read the manual first before you get too far or better off hire Certified Installer to do it for you.
If you still feel like messing with it watch this video
VIDEO
Thanks for all your help guys, I have a certified Tech, but he doesn't know why this isn't working.... There is a lot of pressure from the top to figure this one out, which is why I am reaching out on here. I have updated 10-58 this morning, and everything is still working locally. There was nothing in the routing there before hand. Have to wait a few hours for the employees to get in at the remote location, I will be sure to update this thread when I know if it worked or not. ubuild - thanks for the video
Thank you Coral Tech - That was the issue!!!!! I added 10.1.10.0 & 192.168.3.0 to 10-58 and it work!!!!
Btw, have you disabled sip alg
yes sip Aalg was disabled
Coral Tech check your PMs, I really want to talk to you.