atcomsystems.ca/forum
Posted By: teldata1 NEC SV9100 10.XX - 11/15/20 05:37 PM
Does anyone know if having the D Chanel in the same group as the rest of the PRI trunks could cause problems I have always put the D Chanel in group 0

I have been ask to troubleshoot a SV9100 CP10 10.XX that has been having intermittent problems processing calls mostly incoming

I have a copy of the database just looking it over and saw this

I think the channels are getting locked up or not disconnecting properly from what they are telling me and then they reboot the phone system and all is well for a while

just wondering

Thanks

JD
Posted By: Coral Tech Re: NEC SV9100 10.XX - 11/16/20 12:27 AM
It should be in the same trunk group. The check your clocking.
Posted By: teldata1 Re: NEC SV9100 10.XX - 11/21/20 11:47 PM
OK


so they believe the CPU 10 or programing is corrupt and the want me to re key the data base by hand which I have done as of today we are going to be working with Optus
on transferring the licenses over to the new CPU 10

They want to replace the CPU and reprogram the CPU from scratch

I am using a CPU from our Demo Kit (48 Port) I had to turn on Free 10 day License

They have a mix bag of multi button phone IP Phones and single lines phones its a nursing home

I am trying to figure out how to get the voice mail greetings onto the new CPU Optus mentioned using In mail utility which I haven't used on the SV 9100 CP10

also I saw in the program that 0 (Zero) is a virtual extension number and cant figure out how they did that

Just wondering if anyone has had to replace a CPU


Thanks


JD
Posted By: Meyery2k Re: NEC SV9100 10.XX - 11/22/20 07:40 PM
Something to check. I had a system behaving very similar on a PRI. It was thought by NEC, and me, that the CPU might be bad. I powered down the system and discovered that, even though the CPU screws were tight on the chassis, the card itself was able to be inserted into the system quite a bit. After that, the problems quit. Make sure all your cards are well seated into the backplane.

If you can get help from NEC or Optus, it is also quite easy to run a D-Channel trace and, if you can duplicate the trouble, see if this is a provider problem.

If the voice mail has many mailboxes and messages, In Mail utility would be the easiest way. If it is small and you think you can get away with just saving the greetings then logging in as USER1 will allow you to download and upload greetings in all mailboxes. If there is not too much work then you can also download messages. The NEC uses a naming convention that allows you to easily figure out what greeting goes to what mailbox.
Posted By: teldata1 Re: NEC SV9100 10.XX - 11/22/20 10:44 PM
This is Great !

It’s kind of a messed up situation being a nursing home for some reason nobody wants to go there

I’ve never been able to troubleshoot any of this I’m just being asked to help out other people have troubleshooting this and this is what the customer wants


Thanks !!
Posted By: teldata1 Re: NEC SV9100 10.XX - 11/25/20 11:45 PM
Problem Solved!

Customer has been having problems with incoming calls on PRI

Patient phone were programmed for automatic trunk line seizure

The PRI was programmed as Ascending

There where several patient phones that were not hung up correctly

Which would give them access to a Chanel
and the channel on the PRI card would be busy
as long as the phone was off hook

However the carrier would not see that camel as busy
Because there was not a call on it

Anytime a call would come in it would see the Chanel as free but the PRI Chanel was busy

So don’t use automatic trunk line seizure On patient phones

I changed the PRI to descending an change the patient
Phones to dial 8 when you lift handset

So it won’t grab a PRI Chanel until you make a call
Posted By: Meyery2k Re: NEC SV9100 10.XX - 11/26/20 03:28 PM
Great find!
Posted By: paulw Re: NEC SV9100 10.XX - 11/27/20 07:36 PM
Originally Posted by teldata1
Problem Solved!

Customer has been having problems with incoming calls on PRI

Patient phone were programmed for automatic trunk line seizure

The PRI was programmed as Ascending

There where several patient phones that were not hung up correctly

Which would give them access to a Chanel
and the channel on the PRI card would be busy
as long as the phone was off hook

However the carrier would not see that camel as busy
Because there was not a call on it

Anytime a call would come in it would see the Chanel as free but the PRI Chanel was busy

So don’t use automatic trunk line seizure On patient phones

I changed the PRI to descending an change the patient
Phones to dial 8 when you lift handset

So it won’t grab a PRI Chanel until you make a call

I always used to set the trunk select to rotary so if there was a faulty trunk you would not select it every time espcially old analog trunks.
© Sundance Phone System Forums - VOIP & Cloud Phone Help