Hey guys. I'm losing hope with my systems here.I have this question posted in both systems forums and figured i would try it here too. I have an old Executone 648 that i connected to a Zultys MX250 via a T-1. The circuit syncs up and looks like it works for the most part. I can call from one system to the other. The problem i am having is when i transfer a call from Executone to Zultys, the call is dropped. Engineers at Zultys originally told me the reason was because Executone was prepending the dnis digits with a # character. . Zultys sees the # as a delimiter character so it doesn't know what to do with the following digits. I was able to remove the # from the transfer sequence and thought that would fix the problem. It didn't. I get the same results. The Zultys guys are now telling me Executone is dropping the call. Below is a snap shot of the CAS Log of a transferred call.

Does anyone here know what it means ? The 5th line down DSP_ start_dtmf_collection is followed by 3 DTMF digits. Then "End of Dialing". What does the next few lines mean ?

Dec 11 10:58:42:683 - 2 - {0x20009} [147.464] [ptl_fsm] [CAS: 0/11] CAS_PTL_ST_IDLE -> CAS_PTL_ST_WINK_ON Rx 0xf
Dec 11 10:58:42:922 - 2 - {0x20009} [147.703] [ptl_fsm] [CAS: 0/11] CAS_PTL_ST_WINK_ON -> CAS_PTL_ST_WINK_OFF Rx 0xf
Dec 11 10:58:42:924 - 2 - {0x20009} [147.705] [ptl] [CAS: 0/11] Port 0 On(Ptl Notf Wink Off) state st_CC_IDLE
Dec 11 10:58:42:924 - 2 - {0x20009} [147.705] [ptl] [CAS: 0/11] Port 0 SetState: st_CC_IDLE(1) -> st_CC_WAIT_FOR_DTMF(26)
Dec 11 10:58:42:924 - 2 - {0x20009} [147.705] [cas_dsp] [CAS: 0/11] >> DSP_start_dtmf_collection
Dec 11 10:58:43:560 - 2 - {0x20009} [148.341] [cas_dsp] [CAS: 0/11] DSP:digit rx 0x32 2:
Dec 11 10:58:43:758 - 2 - {0x20009} [148.539] [cas_dsp] [CAS: 0/11] DSP:digit rx 0x30 0:
Dec 11 10:58:43:977 - 2 - {0x20009} [148.758] [cas_dsp] [CAS: 0/11] DSP:digit rx 0x31 1:
Dec 11 10:58:45:031 - 2 - {0x20009} [149.812] [ptl] [CAS: 0/11] End of Dialing
Dec 11 10:58:45:031 - 2 - {0x20009} [149.812] [ptl_fsm] [CAS: 0/11] CAS_PTL_ST_WINK_OFF -> CAS_PTL_ST_ANSWER Rx 0xf
Dec 11 10:58:45:031 - 2 - {0x20009} [149.812] [ptl] [CAS: 0/11] Port 0 On(Ptl Notf Answer) state st_CC_WAIT_FOR_DTMF
Dec 11 10:58:45:031 - 2 - {0x20009} [149.812] [ptl] [CAS: 0/11] Port 0 SetState: st_CC_WAIT_FOR_DTMF(26) -> st_CC_SETUP_AWAIT_MEDIA_TRM(6)
Dec 11 10:58:45:031 - 2 - {0x20009} [149.812] [ptl] [CAS: 0/11] media_request_frontend: port 0 ch 4107 media_status 0
Dec 11 10:58:45:040 - 2 - {0x20009} [149.821] [cas_dsp] [CAS: 0/11] DSP:media_info_rsp
Dec 11 10:58:45:040 - 2 - {0x20009} [149.821] [ptl] [CAS: 0/11] Port 0 SetState: st_CC_SETUP_AWAIT_MEDIA_TRM(6) -> st_CC_SETUP_SEND(7)

I doubt that will work. Executone is a very old hybrid system. Zulus, is a IP system. Don't not work well together. Time to upgrade.