atcomsystems.ca/forum
Posted By: Jig Caller ID on SX 200 ICP - 07/20/11 09:21 AM
How do I get the Caller ID to display on the console. I just switched from AT&T to Comcast, and they offer free Caller ID. I'm completely new in this system. What are the steps I have to take for it to display the #name and #number on the console.

Thanks in advance, and please help
Posted By: fifty5footer Re: Caller ID on SX 200 ICP - 07/20/11 10:53 AM
First, make sure the carrier is actually delivering Caller ID to you.
Next, go to form 13, Trunk circuit descriptors.
Find the circuit descriptor for the trunks on your analog/ASU card, and choose 'select options'.
Look for the option "CLASS Trunk" and set it to enabled.
If the Caller ID doesn't display, go to the COS of the console, and make sure option #502 is enabled.
Posted By: AKroger Re: Caller ID on SX 200 ICP - 07/20/11 11:13 AM
Did Comcast bring you in a T-1 or a PRI ?
Posted By: AKroger Re: Caller ID on SX 200 ICP - 07/20/11 11:13 AM
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/20/11 11:23 AM
not sure what PRI is... but they installed a big modem, and the phone lines come through that box...
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/20/11 11:49 AM
I just talked to the installer, he said it is Voice over IP.
Posted By: telephoneguy Re: Caller ID on SX 200 ICP - 07/20/11 01:37 PM
Did it cross-connect to your system as a series of pairs of wires, or as a set of four little wires?

Did the words "Loop-start" come into the conversation at any point?

Of course, the easiest way is to call your local Mitel dealer and have him come set it up.
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/20/11 01:59 PM
don't have a local mitel dealer...
not sure of any of those.. i'll try what post #2 suggested later on...
Posted By: AKroger Re: Caller ID on SX 200 ICP - 07/21/11 06:27 AM
It should tell you on your comcast proposal if they quoted you a PRI, T-1 or LS trunks. That would help to see if you can even get Caller ID. You may only have caller ID outbound.

Your installer should also be able to tell you if he installed a circuit into the 200ICP or tunks
Posted By: Mr.Telephone Man Re: Caller ID on SX 200 ICP - 07/21/11 08:46 AM
follow the cable out of the modem the carrier installed. Is it plugged into the front of the 200ICP to a card called T1/E1
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/22/11 11:35 AM
The cable out of the modem is attach to a wall to a device, which provide few phone jacks, from there it is, wired, using two pair into the phone block, and from there it goes in the 200 ICP.
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/22/11 11:45 AM
I believe the phone lines I'm getting is Voice over IP. A cable wire is attached to the phone modem. And then, (follow the above post). I also called Comcast Tech Support, and verified that I'm suppose to be recieving both name and number for each call.
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/22/11 03:07 PM
The trunk card that I have right now says LS/GS card in white color..

I noticed I have some that are have writings in blue on them. I wonder if I need a blue ONS/Class card for Caller ID? If so where can I buy them?
Posted By: Lightning horse Re: Caller ID on SX 200 ICP - 07/22/11 03:46 PM
Part number on the Trunk Card? And part number of the digital card the console is connected to.ie. 9109-xxx-yyy
Posted By: johnp Re: Caller ID on SX 200 ICP - 07/23/11 06:52 AM
You need a LS CLASS Card
Posted By: telephoneguy Re: Caller ID on SX 200 ICP - 07/23/11 01:22 PM
For LS trunks coming in, as John says, you need an LS/CLASS card to provide CID to the PBX, which will let the console and the Digital Phones see CID. If you want analog phones to see CID, you need an ONS/CLASS card for those phones.

Blue cards were part of a package and can not be added to a system later. If you are going to add cards, you need to add white cards only. In form 4, it will tell you the maximum number of blue cards of each type that is allowed on your system.
Posted By: johnp Re: Caller ID on SX 200 ICP - 07/23/11 05:59 PM
Actually, if it is an ICP, the on board trunks are CLASS
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/24/11 08:25 AM
The Trunk card that I currently have is LS/GS (6cct) 9109-011-000. It is in white letters. Is this the correct trunk card?
Posted By: johnp Re: Caller ID on SX 200 ICP - 07/24/11 01:50 PM
If it is an ICP, on the back is an amphenol connector the brings out some ls class trunks, also several digital and analog extensions
Posted By: Lightning horse Re: Caller ID on SX 200 ICP - 07/25/11 08:34 AM
Jig, I have a feeling that you are not working with a 200ICP. Can you please give us a description of the cabinet(s)? (dimensions and color)
Posted By: telephoneguy Re: Caller ID on SX 200 ICP - 07/25/11 06:38 PM
Jig, if the card says LS/GS, it will not give you Caller ID. You need a card with white lettering that says LS/Class. If it is an ICP, as JohnP says, you can get LS/Class through the on-board trunks without any card.

Are you sure that the wires you traced cross-connect on that card?
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/26/11 09:41 AM
I'm pretty sure the phone line wires connect to the blocks, and then from the blocks, it goes to the LS/GS trunk card in Bay 3, in my system..
Posted By: Jig Re: Caller ID on SX 200 ICP - 07/26/11 09:46 AM
@LightningHorse

The picture of my phone system looks exactly like the one on this page (https://www.vergenetwork.com/Mitel_SX-200.htm) the second picture, with the MX Controller. I have two cabinets, instead of one shown in the picture.
Posted By: johnp Re: Caller ID on SX 200 ICP - 07/26/11 04:08 PM
You need to follow the cable coming out of the back of the mz and find which block it is connected to. Somewhere on that block will be 6 LS/CLASS trunk positions. These will have to be cross connected to the imcoming CLASS trunks.

The system will also need programing to reflect this change.
Posted By: MVSpeed Re: Caller ID on SX 200 ICP - 08/16/11 03:43 PM
Will CID on an SX200ICP with Ground Start lines work? I have a call into our office to get the CSR', I'm not sure if the dial tone provider will offer it on GS lines but if so will the switch support it
Thanks!!!
Randy
Posted By: MVSpeed Re: Caller ID on SX 200 ICP - 08/16/11 03:47 PM
forgot to mention if it matters MX controller with a single CIM just a small property
Posted By: johnp Re: Caller ID on SX 200 ICP - 08/17/11 04:46 AM
No caller id on ground start trunks
Posted By: MVSpeed Re: Caller ID on SX 200 ICP - 08/17/11 07:15 AM
That was what I was remembering but as I get older I doubt my memory ;-) Thanks
Posted By: westerntelephone Re: Caller ID on SX 200 ICP - 08/17/11 02:06 PM
GS Trunks don't work in the controller.
Posted By: telephoneguy Re: Caller ID on SX 200 ICP - 08/19/11 08:04 AM
But with the improved call supervision on an ICP, you probably can convert to LS without any problem.
Posted By: Lightning horse Re: Caller ID on SX 200 ICP - 08/19/11 04:11 PM
Still need the battery break/disconnect signal from the C.O. !
© Sundance Phone System Forums - VOIP & Cloud Phone Help