Adding it one at a time does not work either. the following is the output of my session
GENERAL
choose mode
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 5 0
FROM DIAL# TO DIAL# TYPE INDEX#/SHELF,SLOT,CKT/NODE#
71000 71007 TRUNK 0,9,0
71008 71015 TRUNK 0,8,0
71024 71047 TRUNK 12,3,0
71048 71071 TRUNK 4,3,0
71072 71072 TRUNK 8,3,0
71073 71083 TRUNK 8,3,1
71101 71123 TRUNK 0,4,1
71125 71147 TRUNK 4,4,1
71149 71171 TRUNK 0,5,1
71173 71195 TRUNK 4,5,1
71201 71223 TRUNK 0,6,1
71249 71271 TRUNK 8,4,1
71273 71295 TRUNK 12,4,1
71325 71347 TRUNK 12,5,1
71401 71423 TRUNK 8,6,1
71424 71447 TRUNK 0,7,0
71473 71495 TRUNK 12,5,1
GENERAL
choose mode
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 2
FROM NEW DIAL# - 71301
TO NEW DIAL# - 71301
NUMBERS ALREADY DEF ? (Y/N) n
0 - TRUNK
1 - SLT 2 - KEYSET
3 - KEYSET_V_PAGE 4 - TRUNK_GRP
5 - HUNT_GRP 6 - BOSS_GRP
7 - PUBLIC_LIB 9 - FEATURE
10 - EDIT 11 - BELL
12 - PAGE 13 - MODEM
14 - DID_NUMS 16 - DATA_PORT
19 - PRIVATE_LIB 20 - KEYSET_Z_PAGE
21 - RELAY 22 - DATA_USER
23 - DATA_GRP 30 - CONF
31 - DVMS_MSG 32 - DVMS_PORTS
33 - PAGE_Q 35 - GROUP_CALL
36 - DIAL_SERV 37 - ROUTING_ACC
38 - WAIT_QUE 39 - NETWORK
40 - WIRELESS
choose type
*: 0
ENTER (SHELF,SLOT,CKT) - 4,7,1
GENERAL
choose mode
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 5 0
FROM DIAL# TO DIAL# TYPE INDEX#/SHELF,SLOT,CKT/NODE#
71000 71007 TRUNK 0,9,0
71008 71015 TRUNK 0,8,0
71024 71047 TRUNK 12,3,0
71048 71071 TRUNK 4,3,0
71072 71072 TRUNK 8,3,0
71073 71083 TRUNK 8,3,1
71101 71123 TRUNK 0,4,1
71125 71147 TRUNK 4,4,1
71149 71171 TRUNK 0,5,1
71173 71195 TRUNK 4,5,1
71201 71223 TRUNK 0,6,1
71249 71271 TRUNK 8,4,1
71273 71295 TRUNK 12,4,1
71301 71301 TRUNK 0,7,0
71325 71347 TRUNK 12,5,1
71401 71423 TRUNK 8,6,1
71424 71447 TRUNK 0,7,0
71473 71495 TRUNK 12,5,1
GENERAL
choose mode
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*:
GENERAL
choose mode
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 5 0
(PLIS)
PORTS_LIST
0-PHYS_LOC
1-DIAL_NUM
*: 0
choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM SHELF#- 0 4
TO SHELF#- 4
FROM SLOT# - 1 7
TO SLOT# - 7
FROM CKT# - 0
TO CKT# - 31
Any specific data field (type ? for help)
-
PORTS LIST
SHELF/SLOT/CKT TYPE DIAL# PORT_DB# SHORT & FULL NAMES
4 / 7 / 0 PRI23 --- --- --- : ---
4 / 7 / 1 PRI23 --- --- TEL : TEL
4 / 7 / 2 PRI23 --- --- TEL : TEL
4 / 7 / 3 PRI23 --- --- TEL : TEL
4 / 7 / 4 PRI23 --- --- TEL : TEL
4 / 7 / 5 PRI23 --- --- junk : junk
4 / 7 / 6 PRI23 --- --- TEL : TEL
4 / 7 / 7 PRI23 --- --- TEL : TEL
4 / 7 / 8 PRI23 --- --- TEL : TEL
4 / 7 / 9 PRI23 --- --- TEL : TEL
4 / 7 / 10 PRI23 --- --- TEL : TEL
4 / 7 / 11 PRI23 --- --- TEL : TEL
4 / 7 / 12 PRI23 --- --- TEL : TEL
4 / 7 / 13 PRI23 --- --- TEL : TEL
4 / 7 / 14 PRI23 --- --- TEL : TEL
4 / 7 / 15 PRI23 --- --- TEL : TEL
4 / 7 / 16 PRI23 --- --- TEL : TEL
4 / 7 / 17 PRI23 --- --- TEL : TEL
4 / 7 / 18 PRI23 --- --- BLANK : BLANK
4 / 7 / 19 PRI23 --- --- BLANK : BLANK
4 / 7 / 20 PRI23 --- --- BLANK : BLANK
4 / 7 / 21 PRI23 --- --- BLANK : BLANK
4 / 7 / 22 PRI23 --- --- BLANK : BLANK
4 / 7 / 23 PRI23 --- --- BLANK : BLANK
FROM SHELF#- 0
*: DTDB,4
choose access method:
0-SIGNALING_CHANNEL
1-CARD_LOCATION
*: 0
choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM SIGNALING_CHANNEL#- 0 13
TO SIGNALING_CHANNEL#- 13
Any specific data field (type ? for help)
-
signaling_channel
13
------------
NAME- QSIG-M3
SIGNALING_CHANNEL- 13
MAIN_CHANNEL:
SHELF - 4
SLOT - 7
CHANNEL - 24
B_CHANNEL_NEGOTIATION:
(Exclusive/Preferred)- Exclusive
PROTOCOL_ID (At&t/Etsi/aUstralia/Qsig)- Qsig
PROTOCOL_SIDE: U(User or slave)/N(Network or master)- User
END_OF_DIAL_DIGIT- #
SENDING_COMPLETE for outgoing calls (Y/N)- N
SENDING_COMPLETE for Enblock Incoming calls (Y/N)- N
Send Connected Number to Public Network (Y/N)- N
TRANSIT_COUNTER_CODING (Ecma/Iso)- Iso
FROM SIGNALING_CHANNEL#- 0
Any suggestions?
