|
|
Joined: Dec 2005
Posts: 7,056
RIP Moderator-Mitel, Panasonic
|
|
RIP Moderator-Mitel, Panasonic
Joined: Dec 2005
Posts: 7,056 |
Received, read, and sent changes. John C.
When I was young, I was Liberal. As I aged and wised up, I became Conservative. Now that I'm old, I have settled on Curmudgeon.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Nov 2008
Posts: 30
Member
|
|
Member
Joined: Nov 2008
Posts: 30 |
Thanks John for 911 Routing and tip for 88 dialing. I will change these data today as soon as i goto work.
Guess what, i found MS55-MR4 ( G07.18) module which i ordered couple of years ago and forget all about it. I did printout CDE forms, Features Discriptions, Default CDE, and other info at that time and i trier to filled out some CDE commands in that book but it is not finished may be little bit left. I am going to finish that and on a quiet day connect to SX50 and enter all datas, and do a data dump for future. I also found data dump from friend's hotel which i went and dumped copied on my thumb drive. That will give me some reference to work with. I will implement your suggestions also regarding 911 and 88 dialing.
By the way can i email you the data dump from M55 later for corrections? Can i use your aol address or use email feature from this forum?
I will also try my majicjack again with a powered USB hub may be next to SX50 (currently it in a next building) and see it it makes any difference.
I will keep you updated on my advanture.
Thanks again for all your hepl.
DP
|
|
|
|
|
Joined: Nov 2008
Posts: 30
Member
|
|
Member
Joined: Nov 2008
Posts: 30 |
Hello John, I was looking at M55 software CDE and was wondering what should i use in Command 565 to 5568 (incomming) Reg 6 bits e, f, g. My friends data says e=4, f=1, g=no digits(blank).
Please let me know.
Thanks.
DP
|
|
|
|
|
Joined: Dec 2005
Posts: 7,056
RIP Moderator-Mitel, Panasonic
|
|
RIP Moderator-Mitel, Panasonic
Joined: Dec 2005
Posts: 7,056 |
DP, if you are referring to the DID register, leave it at default. DID is for Direct-Inward-Dial trunks. Completely different card from a LS/GS trunk card. See Register 1 bit 'D' which should be set to '0' or '1'. Setting to '5' or '6' would enable register 6. Otherwise, it's just 'there' and does nothing. Where you have a choice of 'CO', 'DIL', 'DISA', 'DID', or 'E&M', you are concerned ONLY with 'CO', and 'DIL'. Registers 3, 6, and 7 need to be left at default. Also, change the battery on you MS55 firmware pack. It's a CR2032, used in all kinds of stuff. Even Wal-Mart carries it. And, again, you REALLY need to get a local Mitel tech involved. John C.
When I was young, I was Liberal. As I aged and wised up, I became Conservative. Now that I'm old, I have settled on Curmudgeon.
|
|
|
|
|
Joined: Nov 2008
Posts: 30
Member
|
|
Member
Joined: Nov 2008
Posts: 30 |
Hello John, I did not have any luck with Magicjack working with SX-50 so i gave up on that.
Thank You for all help.
DP
|
|
|
|
Forums84
Topics94,513
Posts639,938
Members49,844
| |
Most Online5,661
May 23rd, 2018
|
|
|
0 members (),
164
guests, and
41
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
