sundance-communications.com/forum Forums TDM Business Telephone Systems Panasonic Telephones & Systems KX-T7433 second phone

I have a KX-T7433 and I want to install a seccond telephone into the plug named "TO TEL".
Why is not working?
Regards,
PUIU

The second thelephone is a kx-ts5rm-w

The to tel socket in the 7433 telephone is for a analouge telephone. for this to work you have to have the 4 wires connected to the system and in the modular socket (KXTD series), or on a hibrid card if the system is a KXTDA series system.

If the telephone system is a kxtda series the second digital telephone will only connect through a 76xx series telephone

what is the kx-ts5rm-w, is it a conference telephone, if so it requires a analouge telephone port.

Ken

Thanks,

So, what is my problem.... I have a KX-T7433 at my office but when i leaving the room I need a cordless one. My KX-T7433 have a connection in the back. This is not for other telephones? I should buy a special kind of devices???
I can swith on/off the parallel prom menu but still not working.

Regards,
PUIU

Plug your cordless phone into the back of your 7433. Make sure that you have a 2 pair jumper connected to the port at your MDF, and your jack is wired as an RJ14. You can choose to activate XDP if you want the cordless to be a separate extension, or disable XDP if you want both phones to share the extension. Parallel ringing has to be turned on at the 7433 (pgm 99, 39-1 I think) for the cordless to ring.

Kevhawk, the ring on-off on the uk unit is just dial 691 to turn on and 690 to turn off or like PUIU through the menu on the telephone.

Puiu, any cordless will work, but the pair on the red/green connections in the modular socket or pins 4-5 if numbered must be connected to the system. or if you have a meter show about 25v dc.

Try pluging out the key set and plug in a standard telephone and see if you get dial tone.

if not you will have to get that pair connected to the MDF at the system.

Sorry, what are "2 pair jumper connected to the port at your MDF, and your jack is wired as an RJ14."

Regards,
PUIU

Thats is the wires connected to the telephone socket (rj14) and the telephone system distribution box (MDF).If you are not sure about the wiring , this should be done by a panasonic telephone tech because you could blow ports on the telephone system if done wrong

So, when I plug the cordless phone into a socket from the wall, it's working. Doesn't that means the jack is wired as an RJ14 ?
If I plug it in the back of my 7433 is not working.
Is that because of that 2 pair jumpers ?
Regards,
PUIU

When you say not working, not ringing or no dial tone?

If the cordless works in the same socket that the 7433 is pluged in to it should work at the back of the phone check the cable from the socket to the 7433 and make sure the 4 cables are connected in the modular plug.

No, the cordless is not working into the socket that the 7433 is pluged but is working in any socket where the other extension is pluged. I noticed that the other jacks is only one pair wired, in the middle of jack. My cordless have a 4 wires cable all 4 connected in jacks.
Edit// My system is KX-TD1232

Then the pair of wires to the centre pins of the telephone socket that the 7433 is pluged in to are not terminated at the telephone system for the cordless to work. the 7433 will work fine without them but the cordless has to have the analouge port connect through to the socket.

Whoooow!!! Now I think I understand. To connect the analogue port I have to go at MDF and fix that 2 center wires. Is that simple? Do you think I can do it?

I don't know, for it to work you have to find the pair of wires to that socket at the system and connect it to the correct pins of the MDF.

Connecting it to the wrong pins or causing a short could blow 4 extensions, because the power regulater runs 4 ports, and if it goes then thats 4 extensions dead.

You also will need the correct tools to punch down the wires and to find the correct pair.

If the cordless is working in a other port just call forward your extension to it when you leave

code 7102 ext no

So I try to make that but ......is not working.
I make 7102 than the extension but the extension is made 3 digits and in programing it must dial 4 digits.

Use the fwd button 2 or 7102+ extension number you may have to enter # after extension number

After I dial # it sad is not valid. If the extension is 121 I dial 7102+(0 or 1 or 2)+ extension it sad FWD(ALL) Ext121 but when I call myself from outside yhe system is not forwarding my call.

PUIU. do you have a panasonic kxtd 816 or 1232?

The code for forward is for the uk model and may differ to the romania unit, if it is not working check your user guide

On my unit is writen D1231.
I downloaded user manual and it sad tha same but is not working or I don't understand it. I will search more......
Regards.
PUIU

the outside lines have to be programmed to ring dil 1:1 to your extension to follow a forward, so they would only ring at your phone.

I think you should get someone in to set up the system to do what you want. there is no quick fix
get the analouge port connected to your phone or get the cordless programmed to ring for incoming calls.

I understand..... I should get some technical help.
Thanks for all!!!