Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Database conversion question.
#636048 03/24/20 12:51 PM
Joined: Dec 2018
Posts: 3
Member
OP Offline
Member
Joined: Dec 2018
Posts: 3
I have and old ADIX with software version 6.12 and can no longer connect to the existing CPU card. I do however have a backup of the old database and a new CPU card. is there a way to convert the old dos database up to the windows format so I can just bypass using the dos programmer all together?

Telephone Equipment Search
Re: Database conversion question.
terminills #636064 03/24/20 09:45 PM
Joined: Aug 2006
Posts: 1,653
Moderator-Iwatsu
*****
Offline
Moderator-Iwatsu
*****
Joined: Aug 2006
Posts: 1,653
The only way you can pull this off is to load the DOS version 6.12 into your new CPU using the DOS programmer, then re-connect with the suitable Windows programmer and download again. This will allow you to upgrade to any later Windows version pretty easily.


Sometimes the thoughts in my head get so bored, they go for a stroll through my mouth. This is rarely a good thing.
Re: Database conversion question.
JBean3329 #636076 03/25/20 10:39 AM
Joined: Dec 2018
Posts: 3
Member
OP Offline
Member
Joined: Dec 2018
Posts: 3
Thanks,


That's what I thought but I wanted to be sure.

Re: Database conversion question.
terminills #636081 03/25/20 03:10 PM
Joined: Apr 2005
Posts: 211
Member
Offline
Member
Joined: Apr 2005
Posts: 211
There was an Adix programmer before the ADIX Programmer version 3.2? It actually ran in DOS? Hope I don't have any systems out there needing that!

Re: Database conversion question.
Keyset6 #636105 03/26/20 10:27 AM
Joined: Dec 2018
Posts: 3
Member
OP Offline
Member
Joined: Dec 2018
Posts: 3
The dos programmers weren't that bad(used them up to windows 7 personally). Just a little harder to upgrade the iwatsu.

Re: Database conversion question.
terminills #636108 03/26/20 05:29 PM
Joined: Apr 2005
Posts: 211
Member
Offline
Member
Joined: Apr 2005
Posts: 211
Sounds similar to the DOS programmer we had for Rolm Redwood systems in the 80s. Actually the earlier Procomm was a DOS program now that I think of it. I had it on an IBM PC-Jr.


Moderated by  Jadix, JBean3329 

Link Copied to Clipboard
Forum Search
Most Recent 5 Post
NEC NMC Conf Bridge - delete recordings
by Bull Tone - 04/04/20 09:07 PM
CF All on SL2100
by Yoda - 04/03/20 11:45 PM
DISA setup using PRI DID numbers
by etdiego - 04/03/20 06:39 PM
Western Electric KS-16765 L2 Announcement Set
by Will H - 04/03/20 03:43 PM
SL1100 DTMF Sip
by teleco - 04/03/20 01:47 PM
Who's Online Now
23 members (Yoda, PhoneDoctorLV, BobRobert, dexman, MooreTel, EV607797, Bob3470, newtecky, mongo5150, RATHER BE FISHING, hbiss, brokeda, Arthur P. Bloom, KRRath, Bull Tone, Professor Shadow, paulw, Daniel, nortelvoip, Mercenary Roadie, justbill, Carl Navarro, mbhydro), 175 guests, and 48 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums94
Topics93,610
Posts635,192
Members49,261
Most Online5,661
May 23rd, 2018
Today's Birthdays
arkansasphoneman, J.R. IdacomUSA, kala, MARKROX, Nico, NiteOwlMaint, thedrickCT, William Meyer
Newest Members
Derek B, randyt, Justin FCMI, Link_HC, bryann84
49261 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
Ruben 33
dexman 32
hbiss 15
davetel 11
Daniel 10
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2020
Trusted Partners