|
|
|
|
Joined: Sep 2005
Posts: 34
Member
|
OP
Member
Joined: Sep 2005
Posts: 34 |
I was upgrading the system software on an NEC DS 2000 system and during the upgrade my PC rebooted for no known reason. It was 80% completed when my PC rebooted. Now I can't connect to the system is is stuck in startup mode. I have tried the tips on NEC website but no luck. They are either closed today or their support sucks because I have been on hold for an hour and a half now.
I know my PC and connections are fine because I restored their database to the new system with the same PC.
Any ideas? I had to buy a new system so my customer would not be down.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Nov 2001
Posts: 1,640
Moderator-NEC
|
|
Moderator-NEC
Joined: Nov 2001
Posts: 1,640 |
Right from the NEC website
For THE DS2000
1. Verify that your cables and adapters are correct.
2. Check to be sure you have downloaded the latest Update Utility and the correct system software for your system.
3. Start the Update Utility - but do not press Connect.
4. On your DS2000 CPU, press the reset button.
5. As soon as the top 2 LEDs on the CPU start to flash (alternate red and green), press the Update Utility Connect button. Verify the following:
Status = CONNECTED - LOAD MODE
Type = DS2000
Version = NOT AVAILABLE
6. Press Read and continue with the update process normally.
7. When the upload completes, press the reset button on the CPU.
The DS2000 will restart with the selected software and reinstate the default (factory installed) database.
For the DS1000
1. Verify that your cables and adapters are correct.
2. Check to be sure you have downloaded the latest Update Utility and the correct system software for your system.
3. Start the Update Utility - but do not press Connect.
4. On your DS1000 cabinet, put the Run / Load switch in the (down) Load position.
5. Press the reset button on the cabinet.
6. Press the Update Utility Connect button. Verify the following:
Status = CONNECTED - LOAD MODE
Type = DS1000
Version = NOT AVAILABLE
7. Press Read and continue with the update process normally.
8. When the upload completes, put the Run/Load switch in the up (Run) position and press the reset button on the cabinet.
The DS1000 will restart with the selected software and reinstate the default (factory installed) database.
|
|
|
|
|
Joined: Sep 2005
Posts: 34
Member
|
|
OP
Member
Joined: Sep 2005
Posts: 34 |
ttech,
Sorry I should have been more descriptive. I tried the website fix and it did not work. Does anyone know if using the pcmcia card to upload the software might get around the issue.
Thanks for the info.
|
|
|
|
|
Joined: Dec 2004
Posts: 5,722
Member
|
|
Member
Joined: Dec 2004
Posts: 5,722 |
According to Dave when I had a bad one, NO.
Pull the battery and try a complete upload.
Good luck.
KLD
Ken
---------
|
|
|
|
Forums84
Topics94,298
Posts638,870
Members49,769
| |
Most Online5,661
May 23rd, 2018
|
|
|
0 members (),
99
guests, and
334
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
![[Linked Image from i2.photobucket.com]](http://i2.photobucket.com/albums/y24/donbaker/Phone%20Stuff/baker_telecommunications_inc_small-.jpg)
