atcomsystems.ca/forum Forums TDM Business Telephone Systems Inter-Tel Telephones & Systems Help With AudioCodes VOIP Gateway

I've been trying to get my VOIP gateway working - not sure why it stopped working but i figured a wipe to factory settings would do the trick.
After finding out this didn't i looked on the net and found a guide to configuring a MP104 FXO to work with an Intertel Axxess system.

Apparently the AudioCodes CD software doesn't work with Inter-Tel so I need the Inter-Tel CD part number 827.9162. I have other CDs but not this one. Does anyone happen to have the audiocodes software so i could TFTP it to the gateway and finally set this up?

Thanks!
Andy

Where id you find the howto guide for getting the audiocodes and intertel systems to work? I've been googling with no luck.

I got the software i needed but now the gateway wont' stay connected. Here is the log...

It is connected after this first section...
[Code:24007]
1d:2h:22m:33s MGCP Debug Mode: RQNT 490 ACgw0@MP104 MGCP 1.0
X: 239
R: H/rg(N), H/ci(N)
[Code:24007]
1d:2h:22m:33s MGCP Debug Mode:
200 490 OK

Then it disconnects from the IPRC before this:

[Code:24007]
1d:2h:22m:41s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:22m:41s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:22m:42s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:22m:43s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:22m:44s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:22m:48s MGCP Debug Mode: 200 177677 OK
[Code:24007]
1d:2h:23m:8s MGCP Debug Mode: AUEP 491 ACgw0@MP104 MGCP 1.0
F: I,N,R,S,O,ES
[Code:24007]
1d:2h:23m:8s MGCP Debug Mode:
200 491 OK
I:
N: 10.0.0.32:2427
R: H/rg(N), H/ci(N), hd(N), hu(N), hf(N)
S:
O:
ES: L/hu

Then it reconnects here...

[Code:24007]
1d:2h:23m:8s MGCP Debug Mode: RQNT 492 ACgw0@MP104 MGCP 1.0
X: 240
R: H/rg(N), H/ci(N)
[Code:24007]
1d:2h:23m:8s MGCP Debug Mode:
200 492 OK


and disconnects here:

[Code:24007]
1d:2h:23m:10s MGCP Debug Mode: 200 177678 OK
[Code:24007]
1d:2h:23m:11s MGCP Debug Mode: 200 177678 OK
[Code:24007]
1d:2h:23m:11s MGCP Debug Mode: 200 177678 OK
[Code:24007]
1d:2h:23m:12s MGCP Debug Mode: 200 177678 OK
[Code:24007]
1d:2h:23m:14s MGCP Debug Mode: 200 177678 OK
[Code:24007]
1d:2h:23m:17s MGCP Debug Mode: 200 177678 OK
[Code:24007]


Any idea on what is going on? It only stays connected for a few seconds.

Thanks.
Andy

OK, just after I posted the Debug mode sparked a thought... in the MP1xxFXO_usa file there is a MGCPDebugMode =1 so i changed it to =0
Now i get the following in my log:

1d:0h:12m:35s MGCP command error: code=6 error=Illeagal Endpoint name. at line 1, column 21.
AUEP 537 ACgw0@MP104 MGCP 1.0
F: I,N,R,S,O,ES
[Code:24007]

I've tried a bunch of different names, making sure to change them on the device and in the DB Programming but i can't get it to connect at all.

Any suggestions?

I think i'm very close here!

Thanks,