|
Joined: Jan 2011
Posts: 106
Member
|
OP
Member
Joined: Jan 2011
Posts: 106 |
I have installed a new SBX with PRI. Works great EXCEPT CID name is not seen. I am testing this by sending he last three digits of a DID to a station. Phone rings, see CID number in center of the screen, left side. Extension on right. When answer CID number still there, elapsed timer on right - no CID name. Carrier says they are sending it. Vertical Tech Support says no programing is necessary for CID name to appear. Any help appreciated.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Aug 2003
Posts: 5,154 Likes: 2
Moderator-Vertical, Vodavi
|
Moderator-Vertical, Vodavi
Joined: Aug 2003
Posts: 5,154 Likes: 2 |
In PGM 114, is "CLI Name Display" set to "On"?
|
|
|
|
Joined: Jan 2011
Posts: 106
Member
|
OP
Member
Joined: Jan 2011
Posts: 106 |
Yes - CLI Name Display is set for NAME.
|
|
|
|
Joined: Aug 2003
Posts: 5,154 Likes: 2
Moderator-Vertical, Vodavi
|
Moderator-Vertical, Vodavi
Joined: Aug 2003
Posts: 5,154 Likes: 2 |
I would make sure that the number you are dialing from is not listed in Speed Dial. I "think" the speed dial name (or lack thereof) will be displayed on incoming calls when a number is matched.
Have you, or Vertical, done a TRACE to see if you are indeed getting the name from the Telco?
|
|
|
|
Joined: Jan 2008
Posts: 3,821
Retired Moderator
|
Retired Moderator
Joined: Jan 2008
Posts: 3,821 |
This is the procedure for programming cid name on the phones when using CO lines. I think the second part is necessary when using a PRI as well.
Programming the Admin Station Caller ID via Admin Phone You can use the Phone Admin to program Caller ID for Station 100-101 as follows: From any Admin phone Station: 1) Log in as an Administrator. 2) Press PGM and dial 147. 3) Enter 0103 (for CO Range to Program). 4) Press Flex Button 1. 5) Press 1 for FSK. 6) Press Flex Button 2, then enter 0 (for Number) or 1 (for Name). 7) Press Save to store the setting. 8) Press PGM, then dial 114. 9) Enter 100101 for (Station Range to Program). 10) Press Flex Button 1, then dial 1 for (Turn on Caller ID Display). 11) Press Save to store the setting.
Also check your ISDN programming for the trunks themselves, did conversion type 2 all PRI lines set for ISDN/DID. Unlike the XTS/sts there is no specific option for PRI name in display. The name in display option in pgm 114 is the closest thing to that.
Last edited by Derrick; 08/02/16 10:59 AM.
www.myrandomviews "Old phone guys never die, they just get locked in some closet with an old phone system and forgotten about" Retired, taking photographs and hoping to fly one of my many kites.
|
|
|
|
Joined: Jan 2011
Posts: 106
Member
|
OP
Member
Joined: Jan 2011
Posts: 106 |
Iam "new" to Vertical and started by using a laptop not dial-in codes over the phone. In CO Base, CID Attribute, I have FSK, NAME turned on for all the PRI channels. All the phones show the CID number fine - the name is missing. I have used Trace before but Vertical held my hand doing it. Set DIP switch 2 to off, In LDK Remote Diagnostics, use jennie to get to command line. Not sure what command to use to see incoming CID name/number on PRI? Any help appreciated.
|
|
|
|
Joined: Aug 2003
Posts: 5,154 Likes: 2
Moderator-Vertical, Vodavi
|
Moderator-Vertical, Vodavi
Joined: Aug 2003
Posts: 5,154 Likes: 2 |
I don't do it enough to tell someone else how to do it. You should call tech-support and have them walk you through this.
|
|
|
|
Joined: Jan 2008
Posts: 3,821
Retired Moderator
|
Retired Moderator
Joined: Jan 2008
Posts: 3,821 |
Since cid info both name and number appears on a digital display set pretty much by default, it is my opinion the carrier is not providing the name (or not providing it in the necessary format) no matter what they tell you they are doing.
www.myrandomviews "Old phone guys never die, they just get locked in some closet with an old phone system and forgotten about" Retired, taking photographs and hoping to fly one of my many kites.
|
|
|
|
Joined: Jan 2011
Posts: 106
Member
|
OP
Member
Joined: Jan 2011
Posts: 106 |
Resolved: Vertial Tech Support had me remove the Station Group name and un-check Queue Count Display. This was 1/2 the problem I also found that the Flexible DID table, Name blocks CID name. I put a name in so it is easier to manage the list of DID's. Bad choice with SBX. I removed all the DID names = problem resolved. Carrier also set circuit to Standard ISDN. FYI
|
|
|
|
Joined: Jan 2008
Posts: 3,821
Retired Moderator
|
Retired Moderator
Joined: Jan 2008
Posts: 3,821 |
We didn't have all that info...ringing into a station group, did name etc. Glad you got it resolved.
www.myrandomviews "Old phone guys never die, they just get locked in some closet with an old phone system and forgotten about" Retired, taking photographs and hoping to fly one of my many kites.
|
|
|
Forums84
Topics94,307
Posts638,897
Members49,771
|
Most Online5,661 May 23rd, 2018
|
|
2 members (mongo5150, Toner),
108
guests, and
135
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|