|
Joined: Mar 2009
Posts: 393
Member
|
OP
Member
Joined: Mar 2009
Posts: 393 |
I just installed a 5193 CID module on the COT4 card on an older TDA50 before the G model. AT&T had all their lines out of service at the time so I could not test. The customer now says that even after AT&T fixed all the lines that the CID does not show? I don't recall ever doing any additional programming to get this to work before? What have I missed?
This customer is about 90 miles out from here so I want to be sure I have whatever I need to get this done in one job.
Thanks for any light you can shed.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Mar 2009
Posts: 393
Member
|
OP
Member
Joined: Mar 2009
Posts: 393 |
I just emailed them to be sure they are looking at RINGING phones for the CID and not just the blinking ones as I think this may be the cause of the complaint.
|
|
|
|
Joined: Aug 2009
Posts: 1,116
Member
|
Member
Joined: Aug 2009
Posts: 1,116 |
You may have it turned off in programing..... Also there are 3 types of Caller ID signals in North America wrong settings will stop it from working too!!
|
|
|
|
Joined: Mar 2009
Posts: 393
Member
|
OP
Member
Joined: Mar 2009
Posts: 393 |
Thanks Shawn,
Defaults protocols always worked in the past without doing anything. I must admit this was not my install and I did not look for anything weird deviating from the norm. I'll review the copy of the DYSYS before going.
|
|
|
|
Joined: Aug 2009
Posts: 1,116
Member
|
Member
Joined: Aug 2009
Posts: 1,116 |
Idd have customer plug standard single line caller ID box or capable Cid cordless phone base into each C. O. LINE right in the demarc Jack's and see if info is coming thru .before pointing finger at equipment.... I've had issues with caller ID on tda 50G with voip lines....
Last edited by ShawnC; 03/16/19 04:31 PM.
|
|
|
|
Joined: Aug 2009
Posts: 1,116
Member
|
Member
Joined: Aug 2009
Posts: 1,116 |
Did you give everyone a call log 601 button?
|
|
|
|
Joined: Oct 2007
Posts: 322
Member
|
Member
Joined: Oct 2007
Posts: 322 |
There is also a Caller ID wait timer, the default is 5 seconds. Making it shorter can cause Caller ID not to show.
Instructions are just one man's opinion on paper
|
|
|
|
Joined: Mar 2009
Posts: 393
Member
|
OP
Member
Joined: Mar 2009
Posts: 393 |
Hi Shawn,
If there is a Call log key will the CID show on a station display on one that's in the ICD group but NOT set to ring at all?
C5Z, I would be surprised if the CID was changed but I'll look through the DSYS.
|
|
|
|
Joined: Mar 2009
Posts: 393
Member
|
OP
Member
Joined: Mar 2009
Posts: 393 |
OK I finally got back. The CID problem was solved by merely re-seating the module. I rolled it with a known working one and it worked so I put the original one back and it's fine. I wish they would have had Dialtone when I was there the 1st time as I would have tried that right then. I must say the clips make them much easier to put in than remove.
Of course no good deed goes unpunished. They ALL want CID so I made them all ring and they turned down the ringers if they didn't want to hear it. HOWEVER....... They also have DSS keys for all the extensions and now complain that the lights flash too much when calls come in.
I can't think of any way around THIS though???? .
|
|
|
|
Joined: Dec 2007
Posts: 6,800 Likes: 18
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,800 Likes: 18 |
HOWEVER....... They also have DSS keys for all the extensions and now complain that the lights flash too much when calls come in.
I can't think of any way around THIS though???? . Easy, install a new DSS console next to the original and don't program it ring on incoming calls and place a piece of black construction paper over the bothersome DSS unit. Or just have them unplug the original DSS then it starts getting overwhelming.
|
|
|
Forums84
Topics94,294
Posts638,834
Members49,769
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
114
guests, and
343
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|