web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 3 of 3 1 2 3
Joined: Jul 2007
Posts: 23
Member
OP Offline
Member
Joined: Jul 2007
Posts: 23
Didn't quite make it through the weekend, alarms are back. Alarm stats from the CSU:

NI
LOS-Inactive
AIS-Active
Out Of Frame - Active
Yellow - Inact
Red - Active
Code Violations - Inact
BPV - Inact
Frame Bit Errors - Inact

T1
LOS-Inactive
AIS-Inact
Out Of Frame - Inact
Yellow - Active
Red - Inact
Code Violations - Inact
BPV - Inact
Frame Bit Errors - Inact

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Jan 2007
Posts: 29
Member
Offline
Member
Joined: Jan 2007
Posts: 29
My suggestions for B8ZS zero code suppression - YES is based upon all MSDN links on my network - which are on D4/AMI circuits.

From Mitel docs:
Zero Code Suppression is a method of reducing timing errors by suppressing all-zero codes and replacing them with another bit pattern. Both ends of the link must specify the same type of zero code suppression. Default value is "Yes"

Joined: Jul 2007
Posts: 23
Member
OP Offline
Member
Joined: Jul 2007
Posts: 23
thanks becca1jane - would you mind sending me what the entire config for the link descrips are for your set-up? thanks,

Joined: Sep 2006
Posts: 372
Member
Offline
Member
Joined: Sep 2006
Posts: 372
becca1jane is correct, and as she pointed out earlier both sides must be set to YES. What did the Mitel logs and DT read show? What model CSU are you using?


JimmyV

"Well informed people know it is impossible to transmit the voice over wires. Even if it were, it would be of no practical value" Boston Post, 1865
Joined: Jan 2007
Posts: 29
Member
Offline
Member
Joined: Jan 2007
Posts: 29
I was able to find some MSDN links on our network that were set to B8ZS zero code suppression - NO on both sides. Otherwise all descriptors are similar other than opposites ends of each link being set to A/B for message control.


──────────────────────────────────────────────────────────── ───────────────────│
│ LINK DESCRIPTOR ASSIGNMENT │
│ │
│Digital Link Descriptor Number: 1 │
│ │
Description │ Value │
┌─────────────────────────────────────────────────────────── ┌──────────────────│
│Address for Message Control (A/B). . . . . . . . . . . . . B │
│BER - Maintenance Limit, 10**-n, n=(3,4,5,6) . . . . . . . 4 │
│BER - Service Limit, 10**-n, n=(3,4,5,6) . . . . . . . . . 3 │
│Data Call Alternate Digit Inversion (Yes/No) . . . . . . . Yes │
│Framing Losses in 24 hrs - Maintenance Limit (0-9000). . . 255 │
│Framing Losses in 24 hrs - Service Limit (0-9000). . . . . 9000 │
│Integrated Digital Access . . . . . . . . . . . . . . . . DPNSS │
│QSIG Private Network Access (Yes/No) . . . . . . . . . . . No │
│Vendor Inter-working Type . . . . . . . . . . . . . . . . . │
│Satellite Link Delay (Yes/No). . . . . . . . . . . . . . . No │
│Slip Rate - Maintenance Limit (0-9000) . . . . . . . . . . 255 │
│Slip Rate - Service Limit (0-9000) . . . . . . . . . . . . 7000 │
│Termination Mode (NT/LT). . . . . . . . . . . . . . . . . . │
│Send Malicious Call Indication to PSTN For Tagged Calls . . No │
│ │
│ DS1 Parameters: │
│Alarm Debounce Timer - Service Limit (300-3200). . . . . . 500 │
│B8ZS Zero Code Suppression - (Yes/No). . . . . . . . . . . Yes │
│ │
│ Universal T1 and Enhanced Dual T1 Card only: │
│Operation Mode (CSU/DSX-1) . . . . . . . . . . . . . . . . │
│CSU Tx Line Build-Out(0,7.5,15,22.5 db). . . . . . . . . . │
│DSX-1 line Length(0-133,134-266,267-399,400-533,534-655 ft) │
│Extended Super Frame (Yes/No). . . . . . . . . . . . . . . No │
│Inverted D channel ( DPNSS only ) (Yes/No) . . . . . . . . No │
│ │
│ Universal E1 and Enhanced Dual E1 only: │
│Operation Mode (CSU/DSX-1) . . . . . . . . . . . . . . . . │
│CSU Tx Line Build-Out(0,7.5,15,22.5 db). . . . . . . . . . │
│DSX-1 line Length(0-133,134-266,267-399,400-533,534-655 ft) │
│Extended Super Frame (Yes/No). . . . . . . . . . . . . . . No │
│Inverted D channel ( DPNSS only ) (Yes/No) . . . . . . . . No │
│ │
│ Universal E1 and Enhanced Dual E1 only: │
│CRC-4 enabled(Yes,No). . . . . . . . . . . . . . . . . . . No │
│E1 line Length(0-133,134-266,267-399,400-533,534-655 ft) . │
│E1 Impedance (75,120 ohms) . . . . . . . . . . . . . . . . │
│ │
│ Italian Parameters: │
│Digital Link Fault Delay Timer (0-360 sec) . . . . . . . . 240 │
│ │
│ Universal T1/E1 Coding Conversion Parameters: │
│Voice conversion (Nil/ADI/Invert/Inverted ADI). . . . . . . Nil │
│Data conversion (Nil/ADI/Invert/Inverted ADI). . . . . . . Nil │

Joined: Jul 2007
Posts: 23
Member
OP Offline
Member
Joined: Jul 2007
Posts: 23
jimmy - maint logs and dtstats are a few posts above. beccaj - thanks, that is exactally how I"m set up.... model is Adtran ESF csu dsu.

Joined: Jan 2007
Posts: 29
Member
Offline
Member
Joined: Jan 2007
Posts: 29
You mentioned you are clocking to the CO PRIs at each location - if you do a dt r on the PRIs are you seeing any errors at the time of the activity switch? Hope this doesn't sound stupid, but are both PBX's in the same timezone, or atleast in different timezones so that 1:15 on one PBX is not equal to 2:15 on the other? And is the time set correctly on each?

Joined: Jul 2007
Posts: 23
Member
OP Offline
Member
Joined: Jul 2007
Posts: 23
pri circuits are clean.
machines are in the time zone (across the street) and their time is synched.

Joined: Dec 2005
Posts: 7,056
RIP Moderator-Mitel, Panasonic
*****
Offline
RIP Moderator-Mitel, Panasonic
*****
Joined: Dec 2005
Posts: 7,056
What is the possibility of putting your own cable across the street, at least temporarily? Eliminate every bit of possible telco as a trouble source. I've done this twice, with P-P T1, and the problems ALL dissappeared! And companies were so happy with low cost, they put in a permanent link. Remember, arial may not be possible, but boring under the street probably is! Just make sure whoever does the job is bonded AND INSURED! John C. (Not Garand)


When I was young, I was Liberal. As I aged and wised up, I became Conservative. Now that I'm old, I have settled on Curmudgeon.
Joined: Sep 2006
Posts: 372
Member
Offline
Member
Joined: Sep 2006
Posts: 372
Your last CSU alarm post would indicate the problem is with your carrier. The 2000 on shows a Yellow alarm. You could double check with one of the guru’s in the T1 forum.

NI
AIS-Active
Out Of Frame - Active
Red - Active

T1
Yellow - Active


Network Interface Alarms

AIS Alarm Unframed all-ones received at NI
Out of Frame No framing pattern sync at NI
Red Alarm LOS (loss of signal)/out of frame (OOF) causing red alarm at NI


T1 terminal Interface Alarms

Yellow Alarm Receiving yellow alarm pattern from T1


JimmyV

"Well informed people know it is impossible to transmit the voice over wires. Even if it were, it would be of no practical value" Boston Post, 1865
Page 3 of 3 1 2 3

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,696
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,707 CTX100 install
186,794 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 14
TDKs79 8
pvj 4
Who's Online Now
1 members (Gary S.), 141 guests, and 244 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5