|
Joined: Apr 2006
Posts: 16
Member
|
Member
Joined: Apr 2006
Posts: 16 |
hello all. I am new to this board. we are a small somftware company, with a Nitsuko 124i (I think). we lost power a few days ago, and now when we try to dial out its not using touch tone to dial. when I try to getin into program it using #*#* it gives me alternating tones like its unable to connect. anyone have any ideas?
Tony
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jun 2004
Posts: 1,367
Member
|
Member
Joined: Jun 2004
Posts: 1,367 |
no touch tone or no KEYPAD CONFIRMATION TONE? CALL 1 #*#* password possible ( but unlikely) #*#* has been changed.
with power outage, a brown out or spike might of corrupted the CPU.
try resseting sysytem. if still no then thry powering down reseat all cards, if still no then try powering down, pull all cards except for CPU and slot1 (8DSTU) I suspect there are bigger issues going on here
|
|
|
|
Joined: Apr 2006
Posts: 16
Member
|
Member
Joined: Apr 2006
Posts: 16 |
I unplugged and removed the battery for a minute then reinstalled it. I reset all of the cards, nothing different, I pulled all of the cards and left only the CPU and the card in slot one, same problem. when everything was working, as the system was coming back up the SPK light would flash at a slow rate. now when the system comes up, all of the extentions the SPK light flashes normally, and the reception extention (301) SPK light flashes very fast.
|
|
|
|
Joined: Jun 2004
Posts: 1,367
Member
|
Member
Joined: Jun 2004
Posts: 1,367 |
do they come up at all or do they stay in system startup? Sounds like something is definitely hosed, but to make sure try disconnecting all but 1 of the DDk connectors from the board( the blue connectors that go into the card in slot 1. Sometimes a short can screw things up so by eliminated almost all of the wiring might be able to isolate the problem to something other than a processor.
|
|
|
|
Joined: Apr 2006
Posts: 16
Member
|
Member
Joined: Apr 2006
Posts: 16 |
BillFlippen, thank you for the help. so I when out and disconnected all of the DDk connectors except for extention 301. it still had the same problem. the system seems to come up but can not dial. so I powered down and disconnected the one DDk conector to the CPU board. same problem. the I put the little switch that is next to the battery in the other position, put power to it, and it came up and I am able to get into programming and I can make calls. my question now is, what position is that switch suppose to be in for normal operation? and on the boards there are some red LED's that are flashing. and it seems like when I have diconnected the battery the system forgets everything like the time and date. not this time, time and date are correct. now I need help programming so that it will the auto attendant will direct the calls to the extentions.
|
|
|
|
Joined: Jun 2005
Posts: 18
Member
|
Member
Joined: Jun 2005
Posts: 18 |
accpilot,this is a common problem in 24i,system data gets corrupted execpt date & time,try to reprogramm the system through extn 301,just insert all the cards back,& switch on, are u trying to programm the system through pc or extn 301
|
|
|
|
Joined: Apr 2006
Posts: 16
Member
|
Member
Joined: Apr 2006
Posts: 16 |
Hey sudhi, I have all the cards back in, and it seems to be sort of working. they only way we have ever programmed this system is through one of the phones. are you saying that you have to use extention 301 to program? I have been using my phone to program (316), but I am unable to make the auto attendant pick up the calls.
|
|
|
|
Joined: Jun 2004
Posts: 1,367
Member
|
Member
Joined: Jun 2004
Posts: 1,367 |
NO you can use any display extension.
That switch should be set to HOT, not COLD, Cold is a way of defaulting the sysytem which sounds like what you just did. what version of software do you have, that determines how to program up the VM. enter programming and the first thing showed is the version number.
|
|
|
|
Joined: Apr 2006
Posts: 16
Member
|
Member
Joined: Apr 2006
Posts: 16 |
Hey BillFlippen, thanks for getting back to me. it looks like the version is 1.2R. it seems like I have the VM set up, and when I first got it working the MW light was flashing like normal when there was a message. now I did something and the MW doesn't flash anymore. any ideas?
|
|
|
Forums84
Topics94,512
Posts639,934
Members49,844
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
173
guests, and
31
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|