BCM 400 Base Function Tray

Print Thread

Rate Thread

BCM 400 Base Function Tray #130572 11/04/06 02:59 AM
Joined: Aug 2003 Posts: 5,156 Likes: 5 Gainesville, FL, USA nfcphoneman Moderator-Vertical, Vodavi
nfcphoneman Moderator-Vertical, Vodavi Joined: Aug 2003 Posts: 5,156 Likes: 5 Gainesville, FL, USA	I have to replace the Base Function Tray in a BCM 400 for a customer. If I understand correctly, this is a common problem and Nortel issued a tech bulletin about this. Has anyone changed one out? If so, can you describe the process? Thanks, Larry Gainesville Telephone Systems Jacksonville Telephone Systems

Nortel Phone System Service

Nortel Phone System Service in Canada

Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.

Re: BCM 400 Base Function Tray #130573 11/04/06 05:05 PM
Joined: Dec 2003 Posts: 2,086 Columbus, Ohio, USA NTlayoff Former Moderator-Nortel
NTlayoff Former Moderator-Nortel Joined: Dec 2003 Posts: 2,086 Columbus, Ohio, USA	The function tray replacement that I know of, is because the caps on the board are bad. If that is the case you should also check the MSC card. You need to see if there is a wire soldered on it. If not, you may need to replace it also. FIRST - Do a backup to your laptop. It is pretty straight forward to replace. There are a couple screws in the front. Pull the levers and the tray comes out...only so far. Then remove the cables to the MSC card. (just remember which one goes where) Pull the tray out farther and then remove any other cables holding it in. Presto it is out. If they sent you a whole tray, slide it in, put the cables on, screws in, and its back together again. Just check the caps on the new part, make sure they are the good ones. I think blue(ish) is good.....if I remember correctly. I am trying to remember......I think as long as you didn't replace the disk drive you shouldn't have to worry about software. BCM GUY--Is that correct? If CON is the opposite of PRO Then what is the opposite of Progress?

Re: BCM 400 Base Function Tray #130574 11/05/06 06:46 PM
Joined: Jan 2005 Posts: 826 Omaha, Nebraska, USA BCMguy.com Member
BCMguy.com Member Joined: Jan 2005 Posts: 826 Omaha, Nebraska, USA	What NT said! :thumb: It's pretty much plug and play Larry. If you're not replacing the hard drive or MSC card, there shouldn't be any software to worry about. The new BFT will come with a document that details the procedure. Good Luck! Marty Beutler Follow me on my quest to webify all of us at Webify.Us --> Providing Business Relevance for Web 2.0 Technologies

Re: BCM 400 Base Function Tray #130575 11/06/06 12:38 AM
Joined: Aug 2003 Posts: 5,156 Likes: 5 Gainesville, FL, USA nfcphoneman Moderator-Vertical, Vodavi
nfcphoneman Moderator-Vertical, Vodavi Joined: Aug 2003 Posts: 5,156 Likes: 5 Gainesville, FL, USA	Thanks guys! I appreciate the info. I won't be able to do a backup because I can't even get the BCM to ping. -Larry Gainesville Telephone Systems Jacksonville Telephone Systems

Re: BCM 400 Base Function Tray #130576 11/07/06 07:35 PM
Joined: Dec 2005 Posts: 18 Redding ,CA Dan the Phone Man Member
Dan the Phone Man Member Joined: Dec 2005 Posts: 18 Redding ,CA	test message

Moderated by MooreTel

Hop To

Link Copied to Clipboard

sundance-communications.com/forum Forums TDM Business Telephone Systems Nortel Telephones & Systems BCM 400 Base Function Tray