sundance-communications.com/forum Forums TDM Business Telephone Systems Nortel Telephones & Systems MICS PRI

Hello Fellow Techs...I am currently turning up a Norstar KSU w/MICS 6.0...The protocol is NI-2...I feel I have provisioned it correctly however I receive inbound calls but not able to make outbound calls. If possible I would like one of you experts to kind of walk me through as I would really appreciate it...This is my first Norstar however I am a little more familiar with the Meridian product....I can be reached at (313) 303-4438 - mobile.....Extremely urgent!! Thanks......AJ

PM sent

Make sure that you are set up opposite as carrier Ascending or Descending. Just to add I think the 6.0 software had issues with PRI so once you do get it going just keep an eye on it.

Try this!

How to Install a PRI

The DTI card should go into Slot 4 first. If you have a second card it would go into Slot 3.
One PRI code covers both cards.

To enter the software key code

From Terminals & Sets - Next until get to software keys - Show
Sys ID - Next
Password Keys - Show
Key 1: (enter 1st key code)
Key 2: (enter 2nd key code)
Key 3: (enter 3rd key code)

You must disable the card first, program the card for PRI, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets - Next until get to software keys - Show Sys ID - Next
Next until get to Module Status - Show
Show module - Next
KSU (1): Next or State if using (2) cards
KSU (2): State
( ) Ports Busy - Press Disable or Enable
Disable at Once? – Yes

Protocols & Signaling
Hardware - Show
Show Module - Next
Cards on KSU - Show
Cd1 - KSU: Change to PRI - Show
Card Type PRI - Next
Lines: 001-023 - Next
Protocol: SL1 - Next (check with your Telco Carrier for setting)
Type Slave - Next
Bchanseq: Ascend or Descend - Next (check with your Telco Carrier for setting)
CO Fail: TIA-547A - Next
IF Levels: ISDN - Next
Framing: ESF - Next (usually ESF, check with your Carrier
Internal CSU: ON - Next
{need to have either an external CSU or turn the internal one on. If customer needs to use some channels for data then they'll need a CSU/DSU to split off channels before the 0X32. OR to split off data channels after 0X32 they'll need a Nortel Data Interface (NDI) plus bandwidth allocation key codes}

DSX1 Bld: 000-100
Line Coding: B8ZS (usually B8ZS, check with the Carrier)
ClockSrc: Primary (second card would be secondary)
Users cannot access PRI lines directly through line appearances or line pools (except PRI line pools). All outgoing PRI calls are dialed via intercom using routing codes. When a trunk card is changed to PRI, all existing line appearances for that card are automatically removed.


To Build a Route

Services - Show
Ringing Service - Next to
Routing Service - Show
Show Route: 001 - Show
Dial out: No Number - Leave alone - Next
Use: ( ) - Change to PRI
DN Type: Public

To Build Destination Codes

Routing Service - Show
Routes - Next
Dest Codes - Show
Show destcode: (enter code) - Next
DstCode: (enter code) - Show
Normal: 000 - Change to route built - Show
AbsorbLength: ALL
Don't usually have to worry about Night schedule etc.
Line Set Up

Assign each channel (001-023) as trunk type PRI, Line Type: PRI -A.
PRI Lines are always configured Auto Answer. Never Manual Answer.

Target Lines Programming

From Lines - Show
Show LN: 145 - Show (target line range from 145-275 non-XC SW, 145-336 XC SW)
Target LN - Next
Private to: (extension number) - Next
Rec'd #: (enter digits Telco is sending) - Next
If Busy: to prime - Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None - Next
Aux. Ringer: N - Next
End of list