sundance-communications.com/forum Forums TDM Business Telephone Systems Nortel Telephones & Systems Call pilot serial port Problem??

Print Thread

Rate Thread

Call pilot serial port Problem?? #143931 07/15/09 12:03 PM
Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada ATechguy Member
ATechguy Member Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada	HI! I am trying to connect to Call Pilot 100 SW.Version 2.0,I need to change IP address , I have serial cable with the 3 pins config to manual guide. I set the com port parameters to specs. When i power on hyper terminal and start the C.Pilot it shows X's across the screen ?? Anybody no whats wrong . :confused: Thanks

Nortel Phone System Service

Nortel Phone System Service in Canada

Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.

Re: Call pilot serial port Problem?? #143932 07/15/09 03:24 PM
Joined: Feb 2005 Posts: 1,615 Likes: 1 Toronto, Canada Curlycord Member
Curlycord Member Joined: Feb 2005 Posts: 1,615 Likes: 1 Toronto, Canada	Try Emulation TTY or VT100 in Hyperterminal/File/Properties/Settings =---()))))))))---= www.curlycord.com Toronto, Canada

Re: Call pilot serial port Problem?? #143933 07/15/09 06:21 PM
Joined: Oct 2008 Posts: 298 Alberta, Canada conxtel Member
conxtel Member Joined: Oct 2008 Posts: 298 Alberta, Canada	If memory serves correct, serial port is only active during boot up. You need to press ... (can't remember what key) within 3 seconds of power up to access menus.

Re: Call pilot serial port Problem?? #143934 07/16/09 12:52 AM
Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada ATechguy Member
ATechguy Member Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada	Thanks Guys i will try TTY have tried VT100, CONXTEL: I thought it was suppose to prompt you with (M)modify (Y/N) etc?? Thanks Brett

Re: Call pilot serial port Problem?? #143935 07/16/09 03:32 AM
Joined: Oct 2005 Posts: 4,685 Likes: 4 Ottawa, ON. Canada telemarv Member
telemarv Member Joined: Oct 2005 Posts: 4,685 Likes: 4 Ottawa, ON. Canada	Yes it prompts during boot up. garbled display is a baud rate mismatch. Emulations is not a factor. Marv CCNA, CTUB TeleMarv Services (Retired) Providing telecommunication solutions in Ottawa Canada since 1990

Re: Call pilot serial port Problem?? #143936 07/16/09 09:03 AM
Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada ATechguy Member
ATechguy Member Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada	Thanks Marv , already set 9600 baud but i will try a different setting. Thanks.

Re: Call pilot serial port Problem?? #143937 07/16/09 12:30 PM
Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada ATechguy Member
ATechguy Member Joined: Nov 2006 Posts: 715 Durham/Kaw.Ont,Canada	OKay i got it working real PITA, changed ip address and gateway ip. ,i really don't know why it didn't work the first time ?? Thanks :rofl: