web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Jul 2006
Posts: 40
Member
Member
Offline
Joined: Jul 2006
Posts: 40
Hello. I am attempting to expand my Electra Elite 192 system. I currently have the following card arrangement in my slots:

Slot 1: EMPTY
Slot 2: EMPTY
Slot 3: VMS(4)
Slot 4: ESI-8
Slot 5: ESI-8
Slot 6: ESI-8
Slot 7: COI-8
Slot 8: ESI-8

I tried installing a new ESI-8 card in Slot 3 and moving the VMS(4) card to Slot 2.
I went into MB 7-1 and assigned Slot 3 to ESI no problem, but my system will not let me change the assignment of Slot 2 to VMS, ESI, ANYTHING. It is "stuck" as DTI (Slot 1 is also DTI, and cannot be changed, by the way). Is there a way around this? Any and all help is appreciated. This forum has saved my life in the past!

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Apr 2007
Posts: 1,439
Member
****
Member
****
Joined: Apr 2007
Posts: 1,439
When removing a DTI card you must remove all the programs in the reverse order as they were installed

When you install a DTI you do Prog 7-1 first for the upper and lower of each slot (press recall or redial to move the arrow on the left of the screen up).

so you must delete each slot in reverse.

So if you have a 16 channel DTI programmed in slots 1 & 2, you must delete slot 2 upper, then slot 2 lower, then slot 1 upper, slot 1 lower.

Set them all to 'non' then go back and assign your esi card & VM card.


D

Joined: Jul 2006
Posts: 40
Member
Member
Offline
Joined: Jul 2006
Posts: 40
Thanks for the reply, doghart. I followed your instructions, and I was able to change slot 2 upper to NON, but I still cannot change slot 2 lower, or either slot 1.

Here's some more info: Next to slot 2 lower, after DTI, the display reads "=09". Is this "ghost" DTI card still assigned to something?

Joined: Apr 2007
Posts: 1,439
Member
****
Member
****
Joined: Apr 2007
Posts: 1,439
You may have to delete any trunk programming in 1-11-07 (if set to DID change to CO), and 3 [trns] 91, and 3 [trns] 14 first. ANY changes made from the default programming has to be removed in the reverse order it was put in. This can be a pain, even for a seasoned NEC tech, and you're doing well so far.

The display is showing the first trunk # in that slot.
Slot 1 lower should show DTI = 1
Slot 1 upper should show DTI = 5
Slot 2 Lower should show DTI = 9

I would have to guess whoever switched the system from a T1 to analog trunks did not delete the T1 first, so yes, this 'ghost' t1 card still exists in your system. That would mean your COI card is set up as trunks 17-24? or something similar.

D

Joined: Jul 2006
Posts: 40
Member
Member
Offline
Joined: Jul 2006
Posts: 40
doghart, thanks again for the reply. I changed the settings in 1-11-07 from "E&M" to "CO". I went into MB 3--91, and all available lines (1-12, 17-24) were already set to "CO", and all lines at MB 3--91 were set to "2ND DIAL". I still cannont change card assignments in 7-1. You are exactly right on the COI card trunks being set to 17-24.

FYI, I purchased this 192 system used to replace my existing 48 system. The DTI card(s) were most likely used by the previous owner. I simply swapped the systems and made changes as necessary to get everything working. I've never used a DTI card, so I had no idea what was in store....

Joined: Jul 2006
Posts: 40
Member
Member
Offline
Joined: Jul 2006
Posts: 40
Alright, I have made progress! I had to un-assign all channels in MB 1-11-05 before I could change the assignment of the cards, so now the cards are in and working, but for some reason, my VMS card took ports 37-40, leaving my new ESI(8) card with only 4 ports. How can I push my VMS card to take ports 41-44 and open all 8 ports on my ESI card?

Joined: Jul 2006
Posts: 731
Member
Member
Offline
Joined: Jul 2006
Posts: 731
Delete both cards while they are un-slotted, then program your ESI card 1st, then your VMS-4, slot the ESI 1st, then the VMS & check your ports.


www.phonelinetech.com


"Can I Still Call Out?"
Joined: Jul 2006
Posts: 40
Member
Member
Offline
Joined: Jul 2006
Posts: 40
Everything works as planned now! Thanks, IPKII, and thanks again, doghart!!

Joined: Apr 2007
Posts: 1,439
Member
****
Member
****
Joined: Apr 2007
Posts: 1,439
Glad to help.


Moderated by  ttech 

Link Copied to Clipboard
Newest Topics
Samsung xchange server
by scanjet - 04/07/25 06:37 PM
NEC IP Phones
by juno - 04/04/25 09:05 AM
NEC IP phones rebooting
by jpet621 - 04/03/25 03:03 PM
SV9100 store hours mailbox
by muddybl - 04/03/25 02:10 PM
Forum Statistics
Forums84
Topics94,513
Posts639,938
Members49,844
Most Online5,661
May 23rd, 2018
Newest Members
yeloshak, ty3995, Sippy, sersmith, Taddeo
49,844 Registered Users
Top Posters(30 Days)
Toner 8
Taddeo 5
dexman 3
DeanB 2
Who's Online Now
3 members (yeloshak, Dave Me, scanjet), 251 guests, and 46 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998 - 2025
Powered by UBB.threads™ PHP Forum Software 8.0.0