|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
I recently upgraded my dsx-80 to the new 3.0 firmware and now my system is not recognizing my 8 SLIU analog card. Both of the LED's stay lit up constantly. I really need this fixed because I have no fax and I have other devices on this card that are now nonfunctional. Has anyone run in to this. Thanks for the help!
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Nov 2007
Posts: 369
Member
|
|
Member
Joined: Nov 2007
Posts: 369 |
Check 1201 program for station card assignment. If it is "unassigned" or shows something different than SLIU (Data 3 for 4port SLIU, Data 4 for 8port SLIU)... unseat the card, then delete it. After clearing the slot assignment, reseat the card.
Also check 1211 program for the same slot to ensure it isn't assigned as a trunk card.
If the card doesn't identify, try repeating the first step, but power down the system before reseating the card. Reseat it while the system is powered off, then power up.
"I didn't do it, and I won't do it again"
|
|
|
|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
When you say to delete it do you mean switch it to unassigned?
|
|
|
|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
I tried your suggestions and I still have constant green and yellow LED's. I even tried the card in a different bay and the same thing happened. should I try to reinstall the 3.0 firmware?
|
|
|
|
|
Joined: Nov 2007
Posts: 369
Member
|
|
Member
Joined: Nov 2007
Posts: 369 |
Try downloading the current version 3.05 from the NEC website. There were some conversion issues in the earlier versions.
"I didn't do it, and I won't do it again"
|
|
|
|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
|
|
|
|
|
Joined: May 2008
Posts: 9
Member
|
|
Member
Joined: May 2008
Posts: 9 |
Jonathan,
Did you check the RUN/STOP switch on the 8SLIU card, located just below the LEDs ? Sometimes the switch gets bumped accidentally when a card is removed or installed. Also, if you install a card into the DSX chassis while the DSX System Administrator is connected to the DSX, that card will not become active until the System Administrator session is disconnected.
|
|
|
|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
Thanks DSXguy and eriway! I did check the switch and it is in the correct position. I have also disconnected the SA and still no go. Do I need to do a full system initialization and redo my numbering plan? I would rather not do that but if it would fix the problem I will do it. Thanks again
|
|
|
|
|
Joined: Oct 2006
Posts: 33
Member
|
|
Member
Joined: Oct 2006
Posts: 33 |
If both LED's stay on steady, it usually indicates that the card has failed.
|
|
|
|
|
Joined: Sep 2009
Posts: 6
Member
|
|
Member
Joined: Sep 2009
Posts: 6 |
I was afraid of that.....Does it make sense that doing a firmware upgrade would cause the card to fail?
|
|
|
|
Forums84
Topics94,513
Posts639,937
Members49,844
| |
Most Online5,661
May 23rd, 2018
|
|
|
0 members (),
234
guests, and
46
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
