|
|
Joined: Oct 2004
Posts: 1,057
Member
|
|
Member
Joined: Oct 2004
Posts: 1,057 |
I'm trying to resurrect an older OS2 Repartee system, using a 4 Port Mitel COV integration.
I have 4 different 'tested' Dialogic D42SX boards, and I know the system key is working properly.
If I start the system without a Dialogic board installed, I get all the way to the log-in screen, and I can do all of my system programing, including the "Easy Made Switch Set up".
When I install a Dialogic board, and power the unit back up, it goes almost all the way through the boot process, but stops just short of giving me the log in screen.
I get the "Dialogic Board Succesfully Installed", and the "VOXB0 Starting" prompts.
The last thing on the screen says "Using Speed Control Slow Down Range" -1...-3.
That's where is stops.
Any suggestions???
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Sep 2004
Posts: 4,220 Likes: 2
Member
|
|
Member
Joined: Sep 2004
Posts: 4,220 Likes: 2 |
Couple things but probably the biggest is an IRQ conflict of some kind or not the correct IRQ is on the board vs the installed software. Check that first.
Did you reinstall all the software or is this just an existing system you are trying to get the dialogic boards to work?
|
|
|
|
|
Joined: Sep 2005
Posts: 898
RIP Moderator-General
|
|
RIP Moderator-General
Joined: Sep 2005
Posts: 898 |
Yep...what Coral Tech said...did you check the dip switch settings on the the dialogic board before you installed it..? I would look there..sounds like a IRQ conflict to me also...
...bob...
Bob Wells
WellComm, Inc.
"As long as nobody's dead or in jail, it can't be all that bad ! "
|
|
|
|
|
Joined: Aug 2005
Posts: 2,125
Member
|
|
Member
Joined: Aug 2005
Posts: 2,125 |
If I'm not mistaken, that's the point where the dialogic board is downloading its driver info. You might need to reload the Dialogic driver on the hard drive.
I would try renaming the dialogic driver and then copy it from a working system, as a test.
|
|
|
|
|
Joined: Oct 2004
Posts: 1,057
Member
|
|
Member
Joined: Oct 2004
Posts: 1,057 |
Coral;
I deleted the E drive entirely, and did a new install of 7.48, but get the same results.
bob:
I triple checked the D42sx board settings, and they're all set according to the install manual.
During the install process, it shows the Voice board as being assigned IRQ2.
guy:
I tried all of the same steps on an operating system, and everything seems to work just fine.
I'm going to have to assume I've got a bad motherboard?!?!?!
|
|
|
|
|
Joined: Jul 2003
Posts: 1,136 Likes: 1
Member
|
|
Member
Joined: Jul 2003
Posts: 1,136 Likes: 1 |
Does the dongle have integrations enabled?
|
|
|
|
|
Joined: Oct 2004
Posts: 1,057
Member
|
|
Member
Joined: Oct 2004
Posts: 1,057 |
Yup, COV.
I've got 3 or 4 of them, with different features, but I get all the same results.
|
|
|
|
|
Joined: Jul 2003
Posts: 1,136 Likes: 1
Member
|
|
Member
Joined: Jul 2003
Posts: 1,136 Likes: 1 |
If it is an interrupt issue, remember that 2 and 9 are the same
|
|
|
|
|
Joined: Aug 2005
Posts: 2,125
Member
|
|
Member
Joined: Aug 2005
Posts: 2,125 |
Fred, it's also possible that you have one bad ISA port on that Motherboard. You might want to move the cards to another ISA port.
I'm assuming that this is old enough to be ISA Dialogic cards, since it's OS/2. If it's PCI, you might be seeing an old "feature" called PCI Bus-mastering which tended to play hell with what card could be in what slot. In that case, swapping the slots is still the answer.
|
|
|
|
|
Joined: Oct 2012
Posts: 2
Member
|
|
Member
Joined: Oct 2012
Posts: 2 |
Hi, I had the same problem with you, so I did a reinstall and changed the detected irq from 2 to 4, this worked like a charm...
|
|
|
|
Forums84
Topics94,524
Posts640,007
Members49,851
| |
Most Online5,661
May 23rd, 2018
|
|
|
0 members (),
214
guests, and
58
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
