sundance-communications.com/forum Forums Wiring - Telecom Carriers - Trunks & Services Outside Plant OSP Construction Boring through an 18 inch thick brick wall

No, I'm not joking.. Hurricane season is just around the corner, and I'm nearing completion of my french drain project behind my house. However, I'm at the dreaded stage where I need to "bore" a six inch wide hole thru an eighteen inch thick masonry brick retaining wall that bisects my backyard. Since my entire backyard is elevated and surrounded by masonry retaining walls, it's next to impossible to get any heavy machinery back there (boy, a ditchwitch would have been awesome!) I need to accomplish this approximately three feet below ground level. I've dug plenty of clearance around where I need to penetrate the wall. Can anyone share any similar experiences, or offer any advice and guidance to me? I greatfully and sincerely appreciate any suggestions.

Wow Mike, they really sunk that wall into the ground good at 3 feet.

Is the wall solid brick all 18 inches or does it have a concrete filler with brick facade? I have cored 18' poured walls before with an industrial hammer drill and diamond tip coring bits. But, that was only a 3 inch diameter hole. I took a while to get through the wall. The drill got too hot several times, and we had to wait for it to cool down before we could resume drilling again. :bang:

They may make a large enough coring bit for what you need it for.

If not, it looks like hammer and concrete chisel is in your future. Or, you could drill a series of smaller holes and honeycomb it. Then bust it out with a hammer and chisel. Either way, you get to use a hammer and chisel

You can always bust it out as big as you want it, put in the pipe, then fill in around it with the quikrete concrete mix from Home Depot.

Goodluck

I know they make 5 inch masonary bits for Hammer drills, maybe you could rent one. You'd need the bit and drill as it would require a heavy duty drill. I wouldn't be surprise if they make larger bits also. (coring bit) thanks Richard I couldn't remember what they are called.

Maybe you could rent one of these from one of our sparkie buddies!

https://www.toolsdir.com/shopping/nprd.asp?ID=55

or here is you 6 X 18 bit

https://www.bamanufacturing.com/rc_series.html

Mike:

6" is going to be tough. There are concrete coring companies that can do this, but it's going to be expensive. If I were faced with such a situation, I would probably drill a circle of holes with a normal-sized bit in a hammer drill, "connect the dots", then knock out the remaining brick from either side with a hammer and chisel.

Glad it's you and not me. That's a project to say the least.

Thank you for your quick responses, Rich, Bill, breed, and Ed. How would I describe this wall..Sorry, I'm not a brickmason. The wall "retains" a 2.5 to 3 foot high "step" in the ground level. The "high" side of the wall is lined with an 8" thick inner row of "mortor filled" cinderblock. This cinderblock lining is "mortered" up to an 8" thick red brick wall for appearance facing to the lower side of the yard. I've used a masonry miter saw to cut pavers before, but never drilled thru a brick wall. I think it's too thick for the honeycomb approach. I think what I really need is a cannon, and a clear field of fire. I'm thinking seriously about something to the affect of breed's suggestion..

It's called a core drill and it is used with a core drilling rig that attaches to the wall with anchors. You really don't want to consider purchase, we are talking big bucks. Either rent or have a contractor handle it.

-Hal

I'll probably go with a contractor on this one. I'll take a "during" pic of this getting done and post it here, just in case someone ever runs into a situation like this. Thanks everyone for the suggestions and guidance.

Core drilling is not that hard,Rent a core drilling machine and bit from a rental yard ,it will take minutes, If you have allready dug the hole for access that is the hardest work,If the hole is deep enough you can brace the machine in the hole ,you need to rent one that will drill horizontal. core drilling is exspensive ,Most companies charge a minimum of $300 . They charge by the diameter tmes depth. I think you can rent a machine for $75 a day.

Thanks Gene. The 3 foot deep drain trench is dug all the way up to the High-ground side of the wall, so I can go in at or just below ground level from the low-ground side. I'll see what I can find around here.