Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Apr 2007
Posts: 26
fs483 Offline OP
Member
OP Offline
Member
Joined: Apr 2007
Posts: 26
Hello,

I'm trying to understand the difference between the zone definitions on a DSC.

Here's what I got :

01 Delay 1 03 Instant 04 Interior 05 Interior, Stay/Away
06 Delay, Stay/Away
25 Interior, Delay
32 Instant, Stay/Away

I want to configure my system to arm all the windows and door contacts AND the basement motion sensors only when I sleep. If any of the sensors are tripped, I would like a delay before the alarm rings (just in case I sleep walk and go to basement or open a window during the night smile ). When I go out, I want to arm everything. Delay would only be active if I enter through the Entry/Exit doors. Any other sensors tripped would activate siren immediately.

Here are my zones :

Zone 1 : Main entry/exit Doors
Zone 2 : PIR basement
Zone 3 : Window Contact
Zone 4 : PIR Upstairs
Zone 5 : PIR basement
Zone 6 : Window Contact

If I understand correctly :

Zone Definition Meaning
01 Entry/Exit Doors
03 Contacts
04 PIR
05 Contacts but w/sleep arming
06 ???
25 ???
32 PIR but w/sleep arming

So the correct programming would be :

Protected Zone Zone Definition
01 01
02 32
03 05
04 04
05 32
06 05

Thanks

Telephone Equipment Search
Joined: Oct 2007
Posts: 9
Member
Offline
Member
Joined: Oct 2007
Posts: 9
Hi
Did you get it figured out if not LMK as I can help you. I know DSC very well but I need to know the model of the panel exp PC5010.
Greg

Joined: Apr 2007
Posts: 26
fs483 Offline OP
Member
OP Offline
Member
Joined: Apr 2007
Posts: 26
Hi Soupcue,

No it's still not working at it's full potential. I have it running properly when there's no one in the house. However, I can't seem to get it working in STAY mode. The panel is a PC1616 (new series that replaced eth pc1555mx). It's a DSC 632 board inside with a little bells and whistles.

Thanks


Moderated by  metelcom 

Link Copied to Clipboard
Advertising Sponsor
Most Recent 5 Post
Coaxial Cable
by dexman - 03/04/21 03:53 AM
Netlink or CCIS
by Yoda - 03/02/21 02:32 PM
SX200 ICP & ASU Bad ports
by Barrontel - 03/02/21 03:15 AM
NEC SV8100 Inmail Utility
by Sam Juniper - 03/01/21 11:02 PM
IP office and routing calling groups
by High Mesa Communications - 03/01/21 10:56 PM
Popular Topics (Views)
Forum Statistics
Forums95
Topics94,282
Posts639,048
Members49,425
Most Online5,661
May 23rd, 2018
Today's Birthdays
oldtimer1
Newest Members
Sam Juniper, B Ledford, Jonie4, James Wright, TechnoloJay
49,425 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
dexman 23
Ruben 22
pvj 11
Linked Banner to your Product or Website
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Who's Online Now
31 members (phonemeister, sundance, byacey, dexman, RATHER BE FISHING, justbill, hitechcomm, Mercenary Roadie, newtecky, BobRobert, hbiss, jeffmoss26, oldpoleclimber, JBean3329, Touch Tone Tommy, kjwiewall, High Mesa Communications, Coral Tech, dans, telecom guy10, Daniel, Canteleco, Ruben, Yoda, nfcphoneman, Joel J., Bob3470, Avidcomm, Professor Shadow, pvj, Biztel Cuban Okie Tech), 625 guests, and 46 robots.
Key: Admin, Global Mod, Mod
Custom Island 58
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners