EMP & Lightning Home Surge Protection
EMP - Click Here!
Phone.com 300x250
300x250 Your Business Phone Service in the Cloud
Global Test Supply
Turn your commission checks on autopilot with 50% RECURRING COMMISSIONS!
Meticore Weight Loss Voted #1.
Get leads. Get sales. Get growing with Getresponse
Get leads. Get sales. Get growing. [2]
Previous Thread
Next Thread
Print Thread
Rate Thread
#483246 11/07/11 11:33 AM
Joined: Nov 2011
Posts: 3
OP Offline
Joined: Nov 2011
Posts: 3
Hello, new to the forum. We currently have a Valcom V-2006A paging system hooked up to Cisco Unity/Subscriber/Publisher going through a Cisco 2811. We are moving over to a VOIP phone system by CudaTel. We have purchased a Cisco SPA-3102 to connect from the CudaTel to the Valcom using the FXS port.

I'm not sure if anyone on the board has worked with the CudaTel system before and tried interfacing with a similar paging system. The CudaTel sees the FXS port as a provider port and requires a line number. As far as I can tell the RJ11 goes directly from the patch panel to the Valcom and would not have a phone number associated to it.

I am not versed in the warranty Valcom provides for their products so along with posting here I have also sent Valcom support an email describing the situation. I am also actively working with CudaTel support to figure this out.

Any help or suggestions provided would be greatly appreciated.

Thank you.

Linked Banner to your Product or Website
#483247 11/10/11 05:46 AM
Joined: Oct 2010
Posts: 40
Joined: Oct 2010
Posts: 40
Although your question has been answered by our support team, I wanted to post the reply on this board.....

There are a couple of possible scenarios:

If an FXO port is available on the SPA-3102, the V-2006A will connect directly to this port. Ensure the battery feed switch (SW6) is in the ON position.

If an FXO port is not available and an FXS or ATA port is utilized, a V-9970 (Station Level Page Adapter) would would be required between the FXS or ATA port and the V-2006A. The V-9970 will answer the incoming call between the first and second ring, then provide a line level output and close an associated relay that will trigger the V-2006A. In this scenario, the battery feed switch (SW6) would need to be in the OFF position.


To test the V-2006A, plug an analog phone into J4 or connect a buttset to the w/bl pair on the block. When off-hook, an intercom dial tone should be heard. From there, enter a desired zone (1-6) or All Call code (0) and page.


Valcom Tech Support

Moderated by  metelcom 

Link Copied to Clipboard
Advertising Sponsor
Popular Topics (Views)
Forum Statistics
Most Online5,661
May 23rd, 2018
Today's Birthdays
daleturb, GaryWJC, Mark F
Newest Members
AndreLS, JimLafleur, EssKayKay, xmestedex, PhoneGuy007
49,469 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
Top Posters (30 Days)
dexman 14
landing page builder
Advertising Sponsor Spot 2
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Who's Online Now
14 members (pvj, Curlycord, justbill, Professor Shadow, RUSS K., BrianS, teldata1, JBean3329, BobRobert, Skunky, BezLovesITAD, telecom guy10, Meyery2k, ffej010), 106 guests, and 75 robots.
Key: Admin, Global Mod, Mod
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners
landing page builder Antiransomware 300x250 Your Business Phone Service in the Cloud