|
|
Joined: Feb 2013
Posts: 107
Member
|
OP
Member
Joined: Feb 2013
Posts: 107 |
All phone in the idcs 100 R2 system seem to be frozen. Rebooting system and phone's won't boot up, just display Firmware version.
All the LED lights on the MCP1 processor are dead, no blinking, no solid lights, nothing!!!
Power supply AC light is solid green( indicating power supply is working)
Any suggestions on what else can be tried?
My thought is that the MCP1 card is dead however I am open to suggestions.
Thanks.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jun 2006
Posts: 3,004 Likes: 4
Moderator-Samsung
|
Moderator-Samsung
Joined: Jun 2006
Posts: 3,004 Likes: 4 |
If your getting no lights on the MCP1 card then I would look at the PSU.
What does the DC light on the PSU show?
|
|
|
|
Joined: May 2004
Posts: 756 Likes: 2
Member
|
Member
Joined: May 2004
Posts: 756 Likes: 2 |
|
|
|
|
Joined: Feb 2013
Posts: 107
Member
|
OP
Member
Joined: Feb 2013
Posts: 107 |
Could the power supply be bad even if the AC LED light was solid green? Thanks.
|
|
|
|
Joined: Feb 2013
Posts: 107
Member
|
OP
Member
Joined: Feb 2013
Posts: 107 |
If your getting no lights on the MCP1 card then I would look at the PSU.
What does the DC light on the PSU show? I am going to have to get back to you later on the DC light status. I can't remember if it was on or off however I do know that it was not as bright as the AC power light. It was either a dim green or off, I am going to have to recheck and get back to you. I am going to try to replace the fuses. P.S. Do you know if a 250V 2amp fuse will work? Thanks.
|
|
|
|
Joined: Apr 2008
Posts: 457
Member
|
Member
Joined: Apr 2008
Posts: 457 |
Bobby Mreen Communications Technician
|
|
|
|
Joined: Aug 2007
Posts: 59
Member
|
Member
Joined: Aug 2007
Posts: 59 |
Wagner Low Voltage (901)870-6104
|
|
|
|
Joined: Nov 2004
Posts: 368
Member
|
Member
Joined: Nov 2004
Posts: 368 |
Look forcaps on far right (2) on the psu if they are swollen replace psu. If caps are not swollen use a meter check dc volts from power supply ( gnd and -55 +5 as labeled on the main board where the pwr cable from the psu plugs into main pcb) If voltages are good lightly touch the 2 square chips (very common failure)right below the station transformers carefull they may be very hot. If not hot replace mcp card and retest.
|
|
|
|
Joined: Feb 2013
Posts: 107
Member
|
OP
Member
Joined: Feb 2013
Posts: 107 |
I wanted to give everyone an update.
Yesterday I replaced the Power Supply and the system started right up. So everyone on here was right on the money with your helpful recommendation.
All the programing was lost but I managed to find a old copy of the database I made and uploaded it back on the system. So now its as good as new.
Thank you very much!!!
Last edited by raidsystemtech; 03/22/14 05:20 PM.
|
|
|
Forums84
Topics94,283
Posts638,765
Members49,764
|
Most Online5,661 May 23rd, 2018
|
|
2 members (Toner, dans),
188
guests, and
171
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|