Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
SIP Trunk between NEC SV8100 & Avaya G450
#571425 05/08/14 09:02 AM
Joined: May 2014
Posts: 28
Member
OP Offline
Member
Joined: May 2014
Posts: 28
I'm testing SIP trunk between SV8100 & Avaya G450. Avaya G450 is SIP Provider. Successful in Register to Avaya SIP Server and can make call from Avaya G450 to SV8100. But I can not make outgoing call from SV8100 to G450 ( Trunk Group 1 Access code 9 + G450's Extension number)
All commands listed as below:

1. PRG 10-40-01 IP Trunk Availability: Active
2. PRG 10-40-02 SIP Trunk Port: 4
3. PRG 10-28-01 Domain Name
4. PRG 10-28-02 Host Name
5. PRG 10-28-04 User ID
6. PRG 10-28-05 Domain Assignement: Domain Name
7. PRG 10-29-01 Outbound Default Proxy: Active
6 PRG 10-29-03 Default Proxy IP Address
7. PRG 10-29-05 Register Mode: Manual
8. PRG 10-29-11 Registrar Domain Name
9. PRG 10-29-12 Proxy Domain Name
10.PRG 10-29-13 Proxy Host Name
11.PRG 10-30-02 User Name
12.PRG 10-30-03 Password
13.PRG 14-05 - Trunk Group 1 for 4 SIP trunks
14.PRG 22-02 - Incoming Call Trunk Setup: DID
15.PRG 22-11 : DDI Translation Table

Anybody have idea about the missing configuration for the SIP trunking?

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571426 05/08/14 11:55 AM
Joined: Sep 2004
Posts: 3,911
Member
*****
Offline
Member
*****
Joined: Sep 2004
Posts: 3,911
You need to "enblock" the out going number. Try appending a "#" I have seen this work on some systems. To work properly you will need to set up an FROUTE table for extension numbering so that you can dial 3 or 4 digits.

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571433 05/08/14 01:38 PM
Joined: Mar 2014
Posts: 359
Member
Offline
Member
Joined: Mar 2014
Posts: 359
try 22-19. Many times you need an outbound CID to get through.

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571434 05/08/14 01:56 PM
Joined: Apr 2005
Posts: 2,388
Member
*****
Online Content
Member
*****
Joined: Apr 2005
Posts: 2,388
You may need to look at 10-23 and 10-40


We get old too soon, smart too late
Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571476 05/09/14 02:00 AM
Joined: May 2014
Posts: 28
Member
OP Offline
Member
Joined: May 2014
Posts: 28
Thanks for all your advice.I already tried all but still not work
@Coral Tech: I dial 9 + telephone number + # and also the F-route with limited digit dialing
@helpifican: Do you mean 21-19 IP Trunk (SIP) Calling Party Number Setup for Extensions? I put the SV8100 extension number in, but couldn't make call also
@dans: I choose the Registration Mode. Should I put my SV8100 IP address in the 10-23 for the Interconnection setup?

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571584 05/12/14 05:46 PM
Joined: Jun 2013
Posts: 89
Member
Offline
Member
Joined: Jun 2013
Posts: 89
What happens when you attempt the call?

If you haven't already, you might try putting the SIP trunk you expect to dial out on onto a line key. When you dial the number do you see it access the SIP trunk on that line key?



GraniteTCS.com
Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571634 05/13/14 06:42 AM
Joined: May 2014
Posts: 28
Member
OP Offline
Member
Joined: May 2014
Posts: 28
The call is released if I use F-route / 9+extension + # to make call. Busy tone (release tone) is returned back.

I access trunk line 001 to make outgoing call. This trunk line is OK for incoming call.

I use DIM log to get log file for unsuccessful call but no idea for this log:

19:41:43 >>
19:41:43 >><<< cdialsta.cpp(311) Originator dial buffer already opened >>>
regId = 0
CALLED cnetCheckARSDigit() lport=401
ITR_NULL_P_STA: DES_ANSWER_FLAG CLEAR!
ITR_NULL_P_STA: TM_DES_ANSWER_WAIT_L SET!
** CLR_ISDN_FLAG IS CALLED **
** LPORT_W = dc01H **
** CLR_ISDN_FLAG IS CALLED **
** LPORT_W = dc01H **
PK06E10162 PRT CPN num_type == 0, num_plan == 0
create_called_no: size_b 0040H
Call cntrol Recived CAPS

[CC_task data]
Logi_port:0xdc01
len:0x2d
msg_gen:0xa1
primitive:0x04
Line:0x01
Ces:0x01
sapi:0x00
0x08 0x02 0x00 0x04 0x05 0x04 0x03 0x80
0x90 0xa3 0x18 0x03 0xa9 0x83 0x81 0x6c
0x06 0x00 0x81 0x33 0x39 0x30 0x34 0x70
0x05 0x81 0x33 0x34 0x30 0x32 0x7c 0x03
0x80 0x90 0xa3 0x7d 0x02 0x91 0x81 0x00
0x00 0x00 0x00 0x00 0x00
Target System ID is 0
msgPrim :0x04
anaRes.a.crInfo.crSide :0x01
anaRes.a.crInfo.crValue :0x04
š[ipCcRecvCAPS] regId = 0 š
š[ipCcRecvCAPS] p2pChkFlag2, s_logicalPort2 Initialize(0xff)
[ipCcRecvCAPS]CHECK FROM CAPS callInfo_p=(4baa150)
Logical_port:0xdc01
DSP Port 0x101
>>ipCcSipP2PSetting[dc01] invalid spid
RTP PORT:0x2726
RTP Adder:0xc0a81083
Logical_port:0xdc01
IP Adder 0xffffffff
ipCcSipSE() call!!
[ipCcSipSE] : PRIMITIVE (4) Recieved from UPPER_TASK
Create New Call date 01/01/0108 time: 19:41:49
suConnId(15) crValue(4) crSide(1) ccSipCb(4baa21c) size(5300)
>>ipCcSipP2PSetting[dc01] OFF
>>ipCcSipP2PSetting[dc01] OFF
[OGGW] [SETUP->INVITE] state(0) suConnId(15) spConnId(0) crValue(4)
/--- INVITE format information ---/
input format length = 512
made format length = 118
format =
INVITE sip:%s SIP/2.0

From:"%s"

To:

Contact:

Content-Type:application/sdp







[SGW] State(0)->(3) suConnId(15) spConnId(0) crValue(4)
Function Call_cntrol_req
>>>[ipCcRecvSIP]Incoming SIP mesage spid=2 ,cLeg->ifEvent = 21
>>ipCcSipP2PSetting[0] OFF
New CLegId Detected(80000000)
[ICGW] [DISC_IND<-RELIND] state(3) EV(21) EVTYPE(21) MSGTYPE(3) suConnId(15) spConnId(0) crValue(4)
[SGW] State(3)->(c) suConnId(15) spConnId(0) crValue(4)
[ipCcRecvSIP]ipCcFindCr callNum_p=(4baa0c8) cinfo.callNum.crValue=(4) side=(1)
[ipccActivateOtherSE] ipCcCloseRsrc call !!
[ipCcSipSE] : PRIMITIVE (9) Recieved from SIP_TASK
Function Call_cntrol_req OK
T305 TIMER CLEAR !!!
multi_call_control_pro Before-Status:0

multi_call_control_pro After-Status:0

08 02 80 90
GET_CAUSE: Returned value is 16
08 02 80 90
GET_CAUSE: Returned value is 16
Call cntrol Recived CAPS

[CC_task data]
Logi_port:0xdc01
len:0x0f
msg_gen:0xa1
primitive:0x0c
Line:0x01
Ces:0x01
sapi:0x00
0x08 0x02 0x00 0x04 0x4d 0x08 0x02 0x80
0x90 0xa3 0x18 0x03 0xa9 0x83 0x81
Target System ID is 0
msgPrim :0x0c
anaRes.a.crInfo.crSide :0x01
anaRes.a.crInfo.crValue :0x04
[ipCcRecvCAPS]CHECK FROM CAPS callInfo_p=(4baa150)
Logical_port:0xdc01
IP Adder 0xffffffff
ipCcSipSE() call!!
[ipCcTimerSet] !START! (PR_SIP_TIMER_DISC)timerparam->timerval = 60
[ipCcTimerSet] Disc Timer SET! index = 0
[ipCcSipSE] : PRIMITIVE (12) Recieved from UPPER_TASK
Calling party number IE is not available
>>ipCcSipP2PSetting[dc01] OFF
>>ipCcSipP2PSetting[dc01] OFF
[OGGW] [REL->OKor486] state(c) suConnId(15) spConnId(0) crValue(4)
[SGW] State(c)->(0) suConnId(15) spConnId(0) crValue(4)
[ipCcTimerSet] (PR_SIP_TIMER_DISC) !STOP! timerparam->info = 0, timerparam->timerval = 0
[ipCcTimerSet] Disc Timer Stop! index = 0
Delete Call suConnId(15) crValue(4) crSide(1) ccSipCb(4baa21c)
Number of Active call(0)
[ipCcSipSE]:STAT_SIP_NULL -> clean
[CLR rsrcList_p] callInfo_p->rsrcList_p sets NULL!!
ipCcTrRecfgSend() called!!!
Function Call_cntrol_req
Function Call_cntrol_req OK
[rtp_ipinfo]>>>Obtaininig Semaphore is SUCCESS!!.
[rtp_ipinfo]>>>Release Semaphore is SUCCESS!!.
***> Call Information is released. (0x04baa150) <***
T305 TIMER CLEAR !!!
multi_call_control_pro Before-Status:0

multi_call_control_pro After-Status:0

TRK TARGET_DIAL=00000000
hunt_que_del_allstg des_w[dc01]
== Initialize rgt_port_data memory for port:dc01
== rgt_port_data_read(dc01) was 0000
== rgt_des_data_read(dc01) was 0000
ipCcTrRecfgSend() called!!!
Function Call_cntrol_req
Function Call_cntrol_req OK
TRK TARGET_DIAL=00000000
cmain.cpp(3962) Clear RGT Port : Port = 401 Rgt Port = 0
cmain.cpp(3964) Clear RGT des Port : Port = 401 Rgt des Port = 0

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571730 05/14/14 10:58 PM
Joined: Mar 2014
Posts: 160
Member
*****
Offline
Member
*****
Joined: Mar 2014
Posts: 160
I haven't done this before, so my advice maybe not right.
since you could make phone calls from avaya to sv8100, there is nothing wrong with PRG 22-XX.

IF you use F-route, you don't need Access code 9 to get the sip trunks, you could dial the extension numbers directly. I mean they are different things.

IF you could get sip trunk through dialing 9, you could also check configurations on avaya system.

Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571738 05/15/14 01:53 AM
Joined: May 2014
Posts: 28
Member
OP Offline
Member
Joined: May 2014
Posts: 28
Crazyfrog:
Thanks for your advice.
Yah, actually, I tried make call using 2 ways - and both not successful.

1. F-route, I just dial the Avaya extension only.
2. Trunk access code 9 + Avaya extension + #

I searched on internet, there are some suggestion that:

- PRG 20-08-13 - ISDN CLIP: activate
- PRG 21-19 - IP Trunk (SIP) Calling Party Number Setup for Extension

- PRG 84-13-32 DTMF Relay Mode: RFC2833
But it didn't get effect also.


Re: SIP Trunk between NEC SV8100 & Avaya G450
November #571745 05/15/14 09:56 AM
Joined: May 2014
Posts: 28
Member
OP Offline
Member
Joined: May 2014
Posts: 28
I changed some configuration and the outgoing call is working now:

1. PRG 10-28-01 Domain Name: to IP address
2. PRG 10-28-02 Host Name: to IP address
3. PRG 10-28-05 Domain Assignement: IP address

Thank you so much for all you guys for reading and supporting for on this topic.

If you need the screenshot of setting, please PM me.

Page 1 of 3 1 2 3

Moderated by  DrPbx, ttech 

Link Copied to Clipboard
Forum Search
Most Recent 5 Post
Abandoned/Obsolete Armored Copper Drop.
by dexman - 08/06/20 12:10 AM
NEC Cordless Phones
by teldata1 - 08/05/20 09:31 AM
SV9100 Call forwding to voice mail
by teldata1 - 08/05/20 09:24 AM
Help!! Mitel 200 ICP mailbox 0 being hacked
by EPearson - 08/04/20 09:16 PM
Avaya IPO
by bditech - 08/04/20 02:38 PM
Who's Online Now
30 members (jeffmoss26, JBean3329, justbill, hitechcomm, westerntelephone, Professor Shadow, Touch Tone Tommy, CHBDC, metelcom, phonemeister, dans, Ruben, EPearson, Biztel Cuban Okie Tech, Carl Navarro, nfcphoneman, jknichols, RATHER BE FISHING, jab1780, bdunne, Bob3470, Henry VIII, KRRath, R4+Z, Silversam, crazy canuck, vicbob, BobRobert, teldata1, Skunky), 680 guests, and 79 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums94
Topics93,862
Posts636,726
Members49,327
Most Online5,661
May 23rd, 2018
Today's Birthdays
jbrd973, Neely8, please272, Recycler, Vox
Newest Members
jmontler, barryv, carag62, CHBDC, Jeff Jordan
49326 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
dexman 37
Ruben 19
DonaldR 17
hbiss 15
Bluewater Sailing
https://www.patreon.com/bePatron?u=5256033
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2020
Trusted Partners