sundance-communications.com/forum Forums TDM Business Telephone Systems NEC Telephones & Systems SIP Trunk between Asterisk and NEC SL1000

Helllo World.....

I try to configure a sip trunk between Asterisk and NEC SL1000.

My setup is ok from asterisk ---> NEC
I can call extensions from asterisk ( 400-499) ----> NEC ( 100--300).
I setup the incoming trunk like DIL on NEC.

The problem is when i try to call back some extensions from Asterisk via 26-02 Route to Trunk Group ( my trunk group 3)
So if i dial 9 and 4xx the sip trunk is selected.

so my setup is like this :

1. prg 10-40-01 - active
2. prg 10-40-02 - sip trunk port : 4
3. prg 10-28-04 : username : 400 is this correct ?
4. prg10
5. prg 14-05 Trunk 9~12 group 3 Priority 9-12
6. prg 14-11 Trunk 9~12 ID 1-4
7. prg 14-12 Trunk 9~12 Register id -1 Pilot register ID 1
8. prg 14-01 Trunk 9~12 --- > need to put something here ?!
9. prg 10-29 .? need to make something here ?!
10. prg 10-30 user 400 pass 400 ----same on peer details asterisk
11.prg 10-36 user id 400 authid 400 pass 400 same on incoming asterisk


Anybody have idea about what the missing config for the sip Trunking ?!

This is the log file with DIM from NEC:



[Welcome to Aspire remote dim service. Ver2.00] 14/05/21 14:38

ars d tp=0
read error prg260301 table=0
regId = 1
CALLED cnetCheckARSDigit() lport=416
ITR_NULL_P_STA: DES_ANSWER_FLAG CLEAR!
ITR_NULL_P_STA: TM_DES_ANSWER_WAIT_L SET!

===== << 05/21, 14:39 >> =====

** CLR_ISDN_FLAG IS CALLED **
** LPORT_W = dc09H **
PK06E10162 PRT CPN num_type == 0, num_plan == 0
create_called_no: size_b 0040H
Call cntrol Recived CAPS

[CC_task data]
Logi_port:0xdc09
len:0x2b
msg_gen:0xa1
primitive:0x04
Line:0x01
Ces:0x01
sapi:0x00
0x08 0x02 0x00 0x6a 0x05 0x04 0x03 0x80
0x90 0xa3 0x18 0x03 0xa9 0x83 0x81 0x6c
0x05 0x00 0x81 0x32 0x30 0x33 0x70 0x04
0x81 0x34 0x31 0x36 0x7c 0x03 0x80 0x90
0xa3 0x7d 0x02 0x91 0x81 0x00 0x00 0x00
0x00 0x00 0x00
Target System ID is 0
msgPrim :0x04
anaRes.a.crInfo.crSide :0x01
anaRes.a.crInfo.crValue :0x6a

CES : 01 SAPI : 00
[Q.931 Message]
Protocol Descriminator: 08
Call Reference [2 octets]: 80 6a
Q.931 Message Type: 5a

<<<<logicalPort(dc09) is NOT SIP station
This is not SIP terminal. (dc09h)
[CLR rsrcList_p] callInfo_p->rsrcList_p sets NULL!!
ipCcTrRecfgSend() called!!!
Function Call_cntrol_req
Function Call_cntrol_req OK
***> Call Information is released. (0x03e69db8) <***
postoperation.cpp(4385) Not Send Release REQ
itr_exp_voipu_err_ind():action=1,old_status=00d4
Illegal Selector Found !!!!!!! in GET_DISPLAY
TRK TARGET_DIAL=00000000
hunt_que_del_allstg des_w[dc09]
== Initialize rgt_port_data memory for port:dc09
== rgt_port_data_read(dc09) was 0000
TRK TARGET_DIAL=00000000





Now i managed to setup DID table on NEC so i can call from any extension 400~499 to any extension 100~120,201~220,300~304 NEC side.

I think that (for the Registration Mode to SIP server ( Asterisk site)
- No need to configure the PRG10-36 (for other Register ID) if you already configured PRG10-28 & 10-30 (Register ID 0)
- If you use only 1 Register ID 0, just put PRG 14-11 & PRG 15-12 as default 0, not require to change
- Must configure the PRG 10-29 - add the SIP server IP address
Correct me if I'm wrong.

DONE
I'm preparing the document for config

Thanks you guys

Dear amorphys could you please send me the configuration from SL100 0 side because i have the same scenario i will implement between SV8100 and Xercom PABX

[email protected]

Hi amorphys, we are trying to implement SIP trunk between asterisk with SV 8100 .. We did to SIP trunk between two asterisk servers. Kindly share your configuration steps.

Regards,
SaGi

Hi, i send it by mail

give me your email adress

Hi amorphys, we are trying to implement SIP trunk between asterisk with SV 8100 .. Kindly share your configuration steps or email me the steps at [email protected]

Thanks & Regards,
necmy

SIP trunks are setup as DID to start with. If the function is to use them as tie lines then try using froute with e&m config.