sundance-communications.com/forum Forums TDM Business Telephone Systems Panasonic Telephones & Systems DECT Upgrade has system shutting itself down

I just recently finished a DECT phone upgrade on an older TDA50G and have had some problems. It seems that the four new KX-T0155 DECT Cell Stations are drawing too much power and the TDA50 locks up and shuts down every few hours and must be manually rebooted only to fail again a few hours later. I asked the client to unplug two of the four new Cell Stations and they report no further problems since doing that Sunday afternoon.

The system is populated as follows:

Slot 1 = DHLC4

Slot 2 = LCOT4

Slot 3 = DLC8

Doorphone

Last week, I replaced four (4) old KX-T0141 Cell Stations with four (4) new KX-T0155 DECT Cell Stations. There are a total of six (6) KX-DT333B Proprietary Phones connected and the system also has one (1) Doorphone.

I was under the impression that four Cell Stations wouldn't exceed the standard power supply's capacity, but it appears that these have.

Is adding a second power supply to the 7-8 year old TDA50G recommended or should I replace the existing one? In other words, has this configuration really exceeded the capacity of the existing PSU? Or have I done something else wrong? The system worked fine with the old KX-T0141 Cell Stations but upgrading to the KX-T0155s has completely destabilized it.

Thanks in advance for any insights you guys may offer as I'm a bit unsure as to what's the best remedy.

Could this have to do with the version of the cards installed? Is it possible the 7-8 year old DHLC/DLC cards are incompatible with the KX-T0155 Cell Stations? If it's a card compatibility issue, should I be looking for a certain version of card?

Thanks again

if counting the units, a cell station is 4 units,
what does the error log say? if one over is there then it because of over the limit of either cells or units

DHLC\DLC cards need to be 5.002 for dect.
MPR must be 5.0 or later.
Docs show additional AC adapter.

CS needs upgade to 8.0 if using older unit with an 8.0
Check MEC config.

Thanks OBT -

This is the last string of “Minor” errors logged. I don’t know what the code is for “one over” and I’m unsure about how to count units though…

On 3-15-15 at 08:52:30:

Error Code | Sub Code | Error Message

391 | 10102 | Data Link Established
391 | 10101 | Data Link Established
391 | 10103 | Data Link Established
391 | 10104 | Data Link Established

At 16:12:18:

305 | 10103 | Data Link Failure
305 | 10104 | Data Link Failure

At 16:14:24:

10 | 10000 | AC Power Down
11 | 10000 | DC Power Down

At 16:15:49:

2 | 10000 | System Restart

At 16:16:04:

391 | 10101 | Data Link Established
391 | 10102 | Data Link Established

The system hasn’t failed since the “Data Link Established” at 16:16:04 on Sunday - no further errors after client unplugged two of the four Cell Stations and rebooted (except for more Data Link Established errors recorded upon my logging in today).

There were some errors in the Minor error log dating back to April, 2014, so I’m wondering if this CPU is having problems - I saved error log as a “Notepad” doc.

Thanks Brokeda -

I tried to check the DHLC/DLC card version but couldn’t figure out how to find that information. Didn’t see it under “Card Property” or “Port Property” when looking at the individual cards. How do you find this info?

The MPR(M) Version is 5.0003

The Cell Stations are brand new - it says “T0155V4-1B” on the box. I’m not sure how to check MEC config, either but you noted “Docs show additional AC adaptor”, so adding a second PSU sounds like the best place to start, agreed?

Read the manual, goes over MEC and counting power units, thats the install manual.

Configuration/Slot/Summary shows card versions.

Good suggestion to read the manual! I did. I only have 4 KX-T0155 CSs, 6 KX-DT333Bs, one Doorphone and Caller ID card in addition to the built-in HLC and LCOT4 cards, a DLC4 and a DLC8. Based on those devices (if I read the manual power calculations correctly) I shouldn't need a second PSU. Maybe the original is no longer putting out its specified voltage(?) I will meter it and add a second PSU and see what happens. The power calculations don't show a need for an MEC card as configured.

I will also check the card versions next week.

Thanks again, Brokeda

Back onsite now and all that comes up under Configuration/Slot/Summary is 5.0003 for the MPR(M). No version numbers come up for any of the other cards. I assume this means the cards are too old and I should install a new DLC4 to connect the Cell Stations?

I added a second PSU (PNLV6505) and the system has stabilized to the point that it isn't shutting itself down anymore but the new KX-TCA385 DECT phones still act funky - one phone drops offline occasionally and when I try to place an intercom call to it, the message "CS Not Connected" appears on the display of the phone you're calling from. Also, the system time is wrong - it displays PM on the corded phones but the KX-TCA385 displays show AM. Will a new DLC4 card resolve this?