sundance-communications.com/forum Forums TDM Business Telephone Systems Samsung Telephones & Systems OS7200 bridge to os7100 Help

I am looking for help to get 2 systems bridged as one. Let me explain what we have....

The OS7200 is our main system at our main building and that has all 4 of our lines coming in. The OS7100 is in our building down the street and we have the 2 buildings wireless bridges on a 1 GB backhaul system. So we can dial the extension just fine at our 7100 but we need the 7100 system to be able to grab a line from the 7200, we also need to add the 7100 exts to our page group on the 7200. Basically we need the 7100 to act like an extension to our 7200 system. We need to get this going very quickly and get it done ASAP. So any help would be great or i would even be willing to pay someone to help us, but we will want to know how this works and is set up.

What you are looking for is called SPNET, I have listed what you can and can't do via SPNET based on what you are after.

You Won't be able to page extensions from both systems at the same time, you can however page the OS7100 extensions from the OS7200 but this will be a seperate page from the OS7200 page.

You will be able to call out from the OS7100 via the lines on the OS7200.

You Won't be able to have extensions on the OS7100 ring at the same time as extensions on the OS7200.

Why do you have 2 systems? It sounds like you would be better off getting IP extensions off the OS7200 at the 2nd buliding

we have some ip phones at the 2nd location, but we are worried about bringing the bandwidth down to much. We have about 6-8 ip cameras and 4 ip phones. we have a spnet license on both systems already but not sure how we get this all setup. if we can call and setup a page zone for jsut the 7100 extension then i would be good with that.

The bandwidth issue will be the same regardless of the transport - SPNet or IP Phone (but with IP extensions on the remote site the voice traffic goes phone to phone not through the phone system so won't go across the link). For managability I'd go with the IP phone option to the one site: 1Gb backhaul ought to be plenty - the IP phone bandwidth is not much...

Give it a try...

You just program a page group on the OS7100 and a NPAGE key on the 7200.

You're looking at ~32k/s per call for G.729a or ~80k/s per call for g.711 regardless of whether it's spent or not.

I have a site which is running 1 ip phone, 1 pc, and about 12 or so IP cameras back to their main site over a 250MB half duplex wireless bridge with no issues.

I understand the easier way would be to use ip phones. My manager is wanting the 7100 to be able to grab an external line from the 7200 and the be able to page the 7200 system and vis versa. I really would like some help on this. I know a decent amount on this system but i know im no where NEAR where i need to be so i can undertand all this. If someone can email me @ [email protected] i have some questions on how to get this setup and depneding on the price i am willing to pay somone for there time to help me with this.

If you already have the SPNet going and can communicate between the 2 systems, sounds like you need a little more programming to get the trunks across the spnet working. They need to be fixed in did table to work correctly. The paging part is like what nameless says, just make a page group in the 7100 with the phones and then on the 7200 enter the node id and page group using the npage key. It seems as though you have the hard part done. Just need that fine tuning for the 7100 to access the 7200 trunks.

ok so i went through all these steps and i can not for the life of me get my second site to grab an outside line. i have it where you can call between the 2 sites, but how do you grab and outside line from site 2?? i tried the lcr 9 and get nothing but invalid numbers after i start to dial?? I really need some help with this and again if someone is willing to sit down with me for a hour or 2 to help with this i can pay you for your time.

ok so this is where i am at...

went into the nlcr and setup to dial 70 and it triggers the 800 trunk group. well then i hit 00 an it works but the problem it its carrying over the 001800. how do i fix this?? i have tried the modify by deleting digits but that broke it all together. the goal is i want to be able to hit 9 and it grab a outside line from out 7200 so people can dial.