|
Joined: Nov 2006
Posts: 704
Member
|
OP
Member
Joined: Nov 2006
Posts: 704 |
HI! There, I have a site with BCM50 3 Cabinets, with Pri , , I service this site , but never installed it or did the initial programming, The calls are answered AA,CCR Tree Menu, and when u press 1 for sales it has rings a hunt grp 461 with 5 sets in it , 1 of them is x221, ,problem is it is suppose to ring 6 times before going to mailbox , it rings 1 time and goes to 221 mailbox ,instead of ringing the 5 sets,, i think it does the same with the intercom but i may be mistaken,, Cfw Forward busy is off and DND, X221 is prime set for all the pri lines, I disconnected the x221 and it did the same,, i am not certain if they share a common sales mailbox,, the system was rebooted several times , after the 2nd time the phone rang 3 times ,, so i tried again and it went back to 1. It could be the system is has a defective or weak module ,power supply,, ???Okay Spin your wheels .
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
Joined: Jun 2006
Posts: 8,732 Likes: 2
Moderator-Nortel, Computers, General
|
Moderator-Nortel, Computers, General
Joined: Jun 2006
Posts: 8,732 Likes: 2 |
Hunt group should have it's own mailbox. Ext 221 sounds like it has CFNA set to 1.
Scientists say that the universe is made up of Protons, Neutron & Electrons. They forgot "Morons". Dave. (CTUB) Canadian Techs Use Bix!
|
|
|
|
Joined: Nov 2006
Posts: 704
Member
|
OP
Member
Joined: Nov 2006
Posts: 704 |
I checked the CFNA at X221 and it was 6 rings.
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
Assuming the HG queue/timeout is 15 seconds minimum then I would assume the line is told to appear and ring at some set to go into mail that quickly.
Lines must not A&R at a set that is in a HG as per the guide.
|
|
|
|
Joined: Nov 2006
Posts: 704
Member
|
OP
Member
Joined: Nov 2006
Posts: 704 |
Thanks i will check that out,, is it possible there is a short in the wiring or port when it rings ,and the system bounces it into voicemail ??
Last edited by ATechguy; 10/31/17 09:54 PM.
|
|
|
|
Joined: Feb 2005
Posts: 1,615
Member
|
Member
Joined: Feb 2005
Posts: 1,615 |
Noy likely but watch out for Busy Forward on a set that has A&P since the ring count is different at times.
Also watch out for Transfer Callback and DRT timers.
|
|
|
|
Joined: Nov 2006
Posts: 704
Member
|
OP
Member
Joined: Nov 2006
Posts: 704 |
This is pri BlocB assigned to a pool bloc , with 1 line out button that dials a 8 when pressed. Busy forward was not set , but i'll check the timers. Thks
|
|
|
|
Joined: Nov 2006
Posts: 704
Member
|
OP
Member
Joined: Nov 2006
Posts: 704 |
OKay ,Thanks for the tips guys,, i had it solved quickly, Problem is someone had 1 HG phone forwarded all calls to VM port 334 ,, as soon as the grp rang it went to Voicemail box 100 which was assigned to 221 , i also changed the DRT , Call back transfer timers . They were happy to have solved. Many Thnks
|
|
|
Forums84
Topics94,291
Posts638,809
Members49,767
|
Most Online5,661 May 23rd, 2018
|
|
2 members (Toner, nortelvoip),
126
guests, and
402
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|