EMP & Lightning Home Surge Protection
EMP - Click Here!
Global Test Supply
Linked Banner to your Product or Website
eCommerce website for sale!
Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Aug 2009
Posts: 276
Member
OP Online Content
Member
Joined: Aug 2009
Posts: 276
An IP Office 500 v2. All phone screens are suddenly blank but they worked yesterday. There are 4 DS8 + ATM4 base cards. Each one has a steady red LED on port 1 and port 9. No other lights on the base cards. Voltage in all DS ports (1-8) is zero. Unseated all base cards and reseated them one at a time. Turned power off before moving any cards then turned it back on. No change in the leds. In the back, the CPU and SD leds are steady green after boot-up. I power cycled the control unit on and off several times. No change. I unseated and reseated the SD card (after turning off power) but there was no change. Lan and Wan ports blink away when my laptop is attached to them, but my Windows 10 laptop says there is no connection on its ethernet port. Tried DHCP, changing the laptop to 192.168.42.1 and then to 192.168.43.1 (the default IP addresses of the Lan and Wan ports). My laptop still says there is nothing connected to its ethernet port. Cannot ping. IT Person onsite says the phone system has been periodically failing for an hour then coming back on. There have been a lot of rainstorms lately. He suspects power supply is bad. What do you think?


Vaya con Dios amigos!
Butch
Global Test Supply 728x90
Joined: May 2004
Posts: 1,617
Moderator-Avaya
*****
Online Content
Moderator-Avaya
*****
Joined: May 2004
Posts: 1,617
I would try to remove the SD Card and use manager to Reformat and recreate the SD card. Make sure you do with Manager. You may want to try and get the config file of it first as well....

See if it will come up after that. If not, the last resort is to DTE into it, and reload new software.

Instructions here: https://www.ipofficeassistance.com/re-config-ip500-w-dte/

Joined: Aug 2006
Posts: 1,709
Likes: 2
Moderator-Iwatsu
*****
Online Happy
Moderator-Iwatsu
*****
Joined: Aug 2006
Posts: 1,709
Likes: 2
Try unseating all the cards, rebooting the controller and watch the LEDs on the backside if you can see them, then try to connect with Manager. I had a similar situation where a bad port on one of my cards locked everything up. If you can connect at this point, take a complete download in case you have to reformat your SD card, but try re-seating all the cards one at a time to determine if any of the cards is causing your failure.

If no changes, reformat as Mongo suggested.


Sometimes the thoughts in my head get so bored, they go for a stroll through my mouth. This is rarely a good thing.
Joined: Aug 2009
Posts: 276
Member
OP Online Content
Member
Joined: Aug 2009
Posts: 276
IPOffice is so hard.


Vaya con Dios amigos!
Butch

Link Copied to Clipboard
Advertising Sponsor
Popular Topics (Views)
Forum Statistics
Forums94
Topics93,278
Posts634,061
Members49,493
Most Online5,661
May 23rd, 2018
Today's Birthdays
Laura Figueroa, mark dagg
Newest Members
Dave McCann, Mitel Hotel, Jonathan Renaud, dentnshell, Adam Suth
49,492 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
Top Posters (30 Days)
dexman 6
MnDave 3
Advertising Sponsor Spot 2
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Who's Online Now
16 members (BobRobert, MooreTel, Mercenary Roadie, hbiss, Schreiber, tn00247167, Butch Cassidy, dexman, RATHER BE FISHING, metelcom, newtecky, pvj, JBean3329, Yoda, nortelvoip, hitechcomm), 139 guests, and 69 robots.
Key: Admin, Global Mod, Mod
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners
landing page builder Antiransomware 300x250 Your Business Phone Service in the Cloud