|
Joined: Jul 2024
Posts: 2
Member
|
Member
Joined: Jul 2024
Posts: 2 |
hello all, my test and tinker 7200 stoped booting i think the sd card files mite be curruped somewhere, i see there is a "crc error" when loading the ram disk so i think it is the files i dont have any backup's of the licences so may need to update to the 5.0.3 maybe? the files have 495 so i'm guessing thats the version i had pluging into the SIO port i have the boot debug below. MP20s Boot version V0.50 (2013.01.14)
SDRAM : 128 MB (0x80000000) EEPROM : 12KByte CabinetID : MP20S SD Driver Clk : 12MHz Hit 'Q' or 'q' key to stop autoboot: 0 NAND Protection is disabled ...!!! +yCard_Read_File, destPtr(0x81000000) Valid MMC FW flag +InitializeMmcController Eata_init_ata16() Eata_detect_ata16 : Eata ata16v2_identify. Eata_detect_ata16 : Detect Sain Eata device. =============================== General Configuration: 04ca serial number: 20000801 firmware revision: VER 1.23 model: ATA16V2 M2C4-SAIN MMCSM VER 0.12 capabilities (49): 0f00 capabilities (50): 0000 flags (53): 0003 dma (63): 0407 pio (64): 0003 =============================== ... Card is formatted with FAT16 ... f->filename = startup.ini ... f->filesize = 288 ... filetime: 2016-7-21, 14:37:30 ... f->filename = ms2sv125.pkg ... f->filesize = 2025025 ... filetime: 2016-7-21, 14:36:18
Reading a file from MMC card... Done
+yCard_Read_File, destPtr(0x81600000) ... f->filename = startup.ini ... f->filesize = 288 ... filetime: 2016-7-21, 14:37:30 ... f->filename = cs2sv495.pkg ... f->filesize = 1518288 ... filetime: 2016-7-21, 14:36:0
Reading a file from MMC card... Done
+yCard_Read_File, destPtr(0x82000000) ... f->filename = startup.ini ... f->filesize = 288 ... filetime: 2016-7-21, 14:37:30 ... f->filename = rd2sv495.pkg ... f->filesize = 6959038 ... filetime: 2016-7-21, 14:36:36
Reading a file from MMC card... Done
Downloading MSP Image from 0x81000000 ... code_offset=0x80 code_base=800000 data_offset=1d6ff0 code_size=1d6f70 data_base=9d6f70 data_size=114 zeroinit_base=9d7084 prog_entry=100
AIFHEADER: BL_DecompressCode=e1a00000 BL_SelfRelocCode=e1a00000 BL_DbgInitZeroInit=eb00000c EntryPointOffset=ff800100 ProgramExitInstr=ef000011 ImageReadOnlySize=1d6f70 ImageReadWriteSize=114 ImageDebugSize=2444 ImageZeroInitSize=113ac ImageDebugType=224c1 ImageBase=800000 WorkSpace=0 AddressMode=20 DataBase=0 FirstFatOffset=1d9548 Reserved2=1da244 DebugInitInstr=e1a00000 ZeroInitCode[0]=e04ec00f <setup_memory_tags> bd->sdram_bank : 1 Booting ARM0 (MSP) at 0x00000100 ...
Booting ARM1 (CSP) at 0x81600000 ... Linux version 2.6.13-rtl (tacoon@mp10) (gcc version 3.3.2) #241 Wed Nov 25 16:36:42 KST 2015 CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T) Machine: ARM-M825xx2 Comcerto Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Built 1 zonelists Kernel command line: console=ttyS0,38400 root=/dev/ram0 rw initrd=0x82000000,25M ramdisk=81920 ip=10.0.0.2:10.0.0.10:10.0.0.1:255.255.255.0::eth0:off mem=128M PID hash table entries: 1024 (order: 10, 16384 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB = 128MB total Memory: 100736KB available (2523K code, 778K data, 108K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 25600K NET: Registered protocol family 16 Comcerto PCI: init Comcerto PCI: Comcerto device is not configured in PCI host Verify that HBMODE_n(low) pin is high and HBBURSTEN_n(high) pin is low On Mindspeed MH02-D370-xxx board, remove jumper JPCISLV1 SCSI subsystem initialized SPI core: loaded version 0.2 NetWinder Floating Point Emulator V0.97 (double precision) devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. yaffs Nov 25 2015 11:03:38 Installing. Initializing Cryptographic API Crypto engine S/W registered Serial: 8250/16550 driver $Revision: 1.4 $ 2 ports, IRQ sharing enabled Serial: Comcerto 16550 serial driver $Revision: 1.2 $ ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A io scheduler noop registered RAMDISK driver initialized: 1 RAM disks of 81920K size 1024 blocksize loop: loaded (max 8 devices) nbd: registered device at major 43 m825xx_ved: version 0.0.2-2.6cvs m825xx_ved: init SMI NFTL driver: nftlcore.c $Revision: 1.1.1.1 $, nftlmount.c $Revision: 1.1.1.1 $ NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon/Zentel/ESMT NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x08000000 : "OS7100 NAND Flash partition" SPI core: add adapter comcerto-spi NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 Disabled Privacy Extensions on device c02e1578(lo) IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 4 IP-Config: Complete: device=eth0, addr=10.0.0.2, mask=255.255.255.0, gw=10.0.0.1, host=10.0.0.2, domain=, nis-domain=(none), bootserver=10.0.0.10, rootserver=10.0.0.10, rootpath= RAMDISK: Compressed image found at block 0 crc error VFS: Mounted root (ext2 filesystem). mount_devfs_fs(): unable to mount devfs, err: -20 Freeing init memory: 108K Warning: unable to open an initial console. Kernel panic - not syncing: No init found. Try passing init= option to kernel. <7>eth0: no IPv6 routers present
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jul 2024
Posts: 2
Member
|
Member
Joined: Jul 2024
Posts: 2 |
UPDATE.
ok so i found a new sd card that is compatible, copied the old files to it and same issues.... copied the 503 firmware files that i found on here and it now boots.... mostly, dm now connects most settings lost it seems(to be expected tobe fair) still some errors. mainly may "VM_L_UK.tgz" file is damaged also and may other files left from the other sd card are missing or damaged, i wonder does some one have a copy of all the other files from the sd card that i'll need?
PS not looking forward to re-configuring this thing from scratch.....
|
|
|
|
Joined: Aug 2011
Posts: 370
Member
|
Member
Joined: Aug 2011
Posts: 370 |
You may be able to try from one of the keysets copying the database from sys to mcdb....what's the worst that could happen?
PM'd also.
|
|
|
Forums84
Topics94,485
Posts639,828
Members49,831
|
Most Online5,661 May 23rd, 2018
|
|
1 members (justbill),
293
guests, and
27
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|