Hello,
Have a customer that moved into a building with an existing system. Heres the info:
I have a Panasonic KX-TDA50, using 7630 phones. Trying to get 8 port digital station card to work in slot 5. System never sees card.
Software is MPR 1.1022,

Slot 1. KX-TDA5170 4-Port Hybrid Extension Card (HLC4)
Slot 2. KX-TDA5180 4-Port Analog Trunk Card (LCOT4)
Slot 3 KX-TDA5171 4-Port Digital Extension Card (DLC4)
Slot 4 I tried with a 4 port digital, a 4 port CO and empty.
Slot 5 KX-TDA5172 8-Port Digital Extension Card (DLC8)

I have initialized system with only a card in slots 1,2,5 with 8 phones.
There is only one power supply could this be the problem?
Any info would be greatly appreciated.

Doug

Install the card with the console??

No, it's been quite some time since I have done any Panasonic that I needed to use it. I haven't had the software since changing laptops, two laptops ago. Is the second power supply or expand mem required when installing a card in the Slot 5 position ?

No. The system had to be registered to expand beyond 4x4. I have a 12x20 box working just fine and it started to play as soon as I registered it.

I'd check the seating of the expansion card and reregister the system. Yes, I know you don't have access to the dealer website. I guess that's where we jump in and say CALL YOUR DEALER.

The second power supply is only needed when you add the 5th non-76/DT phone.


Carl

a 1.1022 did
not need to be reg'ed

Without needing to register am I able to add an 8 port digital card to slot 5 without using the console ?

I don't remember the software break point, but there were maximums of what would work in the original software releases . . i.e. Carl says that he has one working 12x20, but the original software / box would only work 8 by x.

I will have to agree w/ Carl: CALL YOUR DEALER.

I have 1.0 (I bought 2 of these and were one of the first ones out they shipped the manual to cert dealers later cause it didn't exist and software was in the box) out there still running with double power supplies that did not require A registration and has 9 KX-7436's a 7636 2 cell Stations 4 slts 4 doorphones .The other one I bought also has no rom id is in my house and it has a 12 7600's on it I don't see were you get that it only supported 8x8 that is just not the case....

Hello everyone, I have a problem and decided to register, hopefully I can help someone out along the line.

I have a KX-TDA50 and a KX-TVA50,

the PBX is registered and can see the DLC8 that I installed, I have a CS connected to it working perfectly.

I have the VPS connected in AA Mode 2, I connected in Port 1 of the DLC8 and Port 1 of the VPS.

When logging into the PBX Management Console Version 5 I do not have Extension ports listed under configuration.

When logging into TVA Maintenance Console I cannot use auto configuration, the PBX has been configured for Floating Extension 500 but again I cannot configure the Extension because it does not exist.

My goal is to connect the VPS in DPT with the PBX. I hope this is enough information for one of you pro's out there, I am new the this system so be nice to the noobs out there

Under CONFIGURATION/SLOT
put mouse on the DLC8, a box comes up select port property/look under TYPE on the port you want to use.

When connecting to TDA 50 I got error message stating i had different versions of Pbx software and maintenance console: this is what i have

PBX System TDA 50 Software is MPR 1.1022

Maintenance Console

The following is listed when clicking on “About” button

PBX Unified V7.1.1.4

TDA 50 V1.030
TDA 50 V1.104
TDA 50 V2.000
TDA 50 V3.0.1.24 (API: 3.0.1.7)
TDA 50 V4.0,2,4
TDA 50 V5.0.1.11
TDA 50 V6.0.1.1

Do i need older version of maintenance console?

Not sure. Upgraded all of mine long ago.
May have to check with TS.

Will a KXT7740 DSS Console work with a KXTDA-50 phone system? If so, Do I need to complete any additional programming at the operator position? NOTE: I am connecting it to a KXT-7633 display set. WTD????

Yes in fact it will and it uses a whole dlc port you are not connecting any thing to the 7633 you are pairing it to the 7633 it may be a handful for an end user without toner and wand a PDT and no maint console !
Welcome next time start a new thread don't tack on to an unrelated thread!