No co access on a MICS|Sundance Business VOIP Telephone Help

Print Thread

Rate Thread

No co access on a MICS #142074 02/04/09 09:18 AM
Joined: Dec 2008 Posts: 6 minnesota wuzz OP Member
OP wuzz Member Joined: Dec 2008 Posts: 6 minnesota	Hello.My customer purchased a used mics with a T1 card.I removed the card today terminated my tails and croos connected 3 co's...But I can't seem to get DT.they are set to ring and appear,loop start etc.But when grabbing a line I get dead air???Any help here would be great.Thanks John

Nortel Phone System Service

Nortel Phone System Service in Canada

Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.

Re: No co access on a MICS #142075 02/04/09 09:24 AM
Joined: Aug 2004 Posts: 9,159 Likes: 17 SOUTH TEXAS RATHER BE FISHING Admin
RATHER BE FISHING Admin Joined: Aug 2004 Posts: 9,159 Likes: 17 SOUTH TEXAS	What CO card do you have in there? In what slot?

Re: No co access on a MICS #142076 02/04/09 09:54 AM
Joined: Oct 2006 Posts: 1,386 Likes: 6 Northeast Iowa Yoda Member
Yoda Member Joined: Oct 2006 Posts: 1,386 Likes: 6 Northeast Iowa	Are you grabbing a co line, or a line pool? what is the Prime Line set for?

Re: No co access on a MICS #142077 02/04/09 10:59 AM
Joined: Dec 2008 Posts: 6 minnesota wuzz OP Member
OP wuzz Member Joined: Dec 2008 Posts: 6 minnesota	I have 1 ds card in slot 2.I believe its grabbing line pool a.And not sure what prime line is set for?What should it be?Thanks John

Re: No co access on a MICS #142078 02/04/09 12:47 PM
Joined: Oct 2005 Posts: 4,685 Likes: 4 Ottawa, ON. Canada telemarv Member
telemarv Member Joined: Oct 2005 Posts: 4,685 Likes: 4 Ottawa, ON. Canada	1st line card goes in slot 4. Marv CCNA, CTUB TeleMarv Services (Retired) Providing telecommunication solutions in Ottawa Canada since 1990

Re: No co access on a MICS #142079 02/04/09 05:52 PM
Joined: Mar 2001 Posts: 3,869 Los Angeles, CA Old blond hippity hopping Bunnie Member
Old blond hippity hopping Bunnie Member Joined: Mar 2001 Posts: 3,869 Los Angeles, CA	If this was programmed for a T-1, you have a lot of programming to do. You might be better off to do the STARTUP routine. That should be in your installer guide. THE Bracha, old blond specialist in Rube Goldberg solutions.

Re: No co access on a MICS #142080 02/05/09 03:00 AM
Joined: Oct 2006 Posts: 1,386 Likes: 6 Northeast Iowa Yoda Member
Yoda Member Joined: Oct 2006 Posts: 1,386 Likes: 6 Northeast Iowa	If the you're grabbing Pool A, make sure there are some lines programmed into Pool A. Prime Line should also be set Pool A. Otherwise, program lines to appear and ring on a button, and push the button to get dial tone. All of this after the card is in the right slot, etc., as mentioned above. Jim

Re: No co access on a MICS #142081 02/05/09 03:20 AM
Joined: Dec 2005 Posts: 7,056 Fayetteville, NC Lightning horse RIP Moderator-Mitel, Panasonic
Lightning horse RIP Moderator-Mitel, Panasonic Joined: Dec 2005 Posts: 7,056 Fayetteville, NC	Bunnie's correct,IMHO. Your customer probably has no concept of the MICS's capabilities, and more to the point, YOU have no idea what the previous owner's program was supposed to accomplish. What if the MICS was on a Flash? That was used as an AA/VM, as an example. What if it was arranged for massive numbers of outbound and no inbound, as in 'boiler room' operation. STARTUP is the only way to start from a 'known quantity'. John C. When I was young, I was Liberal. As I aged and wised up, I became Conservative. Now that I'm old, I have settled on Curmudgeon.

Moderated by MooreTel

Hop To

Link Copied to Clipboard

atcomsystems.ca/forum Forums TDM Business Telephone Systems Nortel Telephones & Systems No co access on a MICS