|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
we have a SX2000 and a new T1 line to connect
universal T1 card is installed and configured.
Type: universal t1
> Signal protocol: msdn-dpnss
> BRI Mode: none
> Far end connect: Main PBX
Link Desc: dpnss, dsx-1, nil
T1 settings from provider:
T1 B8ZS line coding, with ESF Framing
PRI encoding is NI2/National
what are the setting required in the SX2000?
thanks in advance.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
A bit more detail.
in the SX2000 Digital Link configuration a DS1 Formatter card provides support for D8ZS/ESF.
Do i need a DS1 card along with the Universal T1 card?
Can a CSU/DSU be installed between the Mitel and the T1?
I am getting ring tone when dialing out the T1, then a recording, "message 3DT1" or "message 4DT1"
thanks.
|
|
|
|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
A bit more detail.
in the SX2000 Digital Link configuration a DS1 Formatter card provides support for D8ZS/ESF.
Do i need a DS1 card along with the Universal T1 card?
Can a CSU/DSU be installed between the Mitel and the T1?
I am getting ring tone when dialing out the T1, then a recording, "message 3DT1" or "message 4DT1"
thanks.
|
|
|
|
|
Joined: Sep 2005
Posts: 2,049
Member
|
|
Member
Joined: Sep 2005
Posts: 2,049 |
What model number universal T1 are you using ?
What version of IMAT have you down loaded to your PC ?
What version lightware are you running on the sx2000 ?
If you can answer these questions maybe someone can help .
Let It Be , I live in a Yellow Submarine . SCCE
|
|
|
|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
thank you for you reply, sorry for not providing that detail.
the t1 card is MC270AA
no IMAT
lightware MS2013-F-NA-00 SX.U03.9.9
I have made some progress. calls are going out and coming in.
however, we have been using circuits requiring a 9, the new T1 does not.
i would like to continue to require the 9 and have it absorbed, but the Digit Mod/Absorb config isn't working.
any suggestions?
thanks.
|
|
|
|
|
Joined: Sep 2005
Posts: 2,049
Member
|
|
Member
Joined: Sep 2005
Posts: 2,049 |
Is this a PRI circuit or a T1 supertrunk ? If it is a PRI you must have IMAT software to configure the PRI card . If it's just a supertrunk you can use a mc270ca . The mc270aa has an onboard csu which is not loopable from the niu . As far as the dial 9 goes put your new trunks in the same digit modification table as your existing ones . The digit mod assignment is under the route table assigment .
Let It Be , I live in a Yellow Submarine . SCCE
|
|
|
|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
there is a mc270ca in the dsu node as well, you are right on.
i use a basic cde terminal to do my config.
we are currently on centrx, which require the 9, at least that's how the programming appears in the Digit Modification form. I want to continue to have staff dial the 9 but have it absorbed before going out.
additionally, when making a call there's no dial tone when selection a line. i am manually selecting the T1 outbound line i want to test.
thanks.
|
|
|
|
|
Joined: Sep 2005
Posts: 2,049
Member
|
|
Member
Joined: Sep 2005
Posts: 2,049 |
On a T1 supertrunk you will not receive CO dialtone on the channels you direct select .That is why you must call route OUTGOING CALLS via ARS . So are you saying they dial 9 and then 9 again for centrex dialtone ?
Let It Be , I live in a Yellow Submarine . SCCE
|
|
|
|
|
Joined: Jan 2006
Posts: 7
Member
|
|
Member
Joined: Jan 2006
Posts: 7 |
got it. i miss typed the route number in the ARS.
thanks.
|
|
|
|
Forums84
Topics94,518
Posts639,974
Members49,850
| |
Most Online5,661
May 23rd, 2018
|
|
|
|
