|
|
|
|
Joined: Apr 2006
Posts: 1
Member
|
|
Member
Joined: Apr 2006
Posts: 1 |
Recently my office was moved but our very old (circa 1990) Meridian PBX (release 17 software) was left a few buildings away. The terminal was also left behind as cost was a factor in moving it. Instead of running back & forth between my office and the PBX terminal I planned on using Procomm but have not had any luck in connecting via modem. I was told that Procomm was the software used by SBC (our contracted repair techs). I have enough knowledge to correct everyday problems using the terminal but SBC will not give me assistance in connecting remotely. I'm using the terminal ID VT-100, 1200 baud, 7 bits even ASCII only emulation, I'm able to make a connection but nothing appears on the terminal screen. It remains blank. Anyone have any suggestions? Thanks in advance Greg [email protected]
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
|
Joined: Aug 2004
Posts: 9,172 Likes: 22
Admin
|
|
Admin
Joined: Aug 2004
Posts: 9,172 Likes: 22 |
There are too many variables. By trying to connect with the wrong parameters you could have disabled the modem port. You need to have an SBC/ATT tech or other Nortel contractor check your port status and modem setup. Good Luck.
|
|
|
|
|
Joined: Mar 2001
Posts: 3,869
Member
|
|
Member
Joined: Mar 2001
Posts: 3,869 |
Pay for some onsite support and call it cheap. You could spend days on this and never get it working.
Many times a little push in the right direction will take care of a defined problem, but I wouldn't waste time on this when you can get it working and know all the settings for the future.
Fishing was right on the money, pay for on-site help.
THE Bracha, old blond specialist in Rube Goldberg solutions.
|
|
|
|
|
Joined: May 2005
Posts: 29
Member
|
|
Member
Joined: May 2005
Posts: 29 |
Try using Port speed 115200 or 9600 and use 8 none and 1. I connect to 3 different switches from Opt. 11,61,and 81 and we use those settings. Hope this was helpful.
|
|
|
|
|
Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
|
|
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086 |
I have seen it happen many times, that even though you are set up for auto baud sensing, you still have to match exactly or it will not display anything for you. I had one that I could connect to everytime, but it displayed nothing. I finally pushed it down to 1200 and it worked just fine. Try them all.
If CON is the opposite of PRO
Then what is the opposite of Progress?
|
|
|
|
|
Joined: Sep 2005
Posts: 2,049
Member
|
|
Member
Joined: Sep 2005
Posts: 2,049 |
There is a MIS you maybe able to set in your Modem Properties . I would follow RBF'S recommendation to hire a Tech to set/check the port parameters and test/verify you can remote access via your PC . Once he/she does that your remote access problems are solved .  :shrug:
Let It Be , I live in a Yellow Submarine . SCCE
|
|
|
|
Forums84
Topics94,529
Posts640,030
Members49,852
| |
Most Online5,661
May 23rd, 2018
|
|
|
|
|
|
![[Linked Image]](https://sundance-communications.com/forum/images/559.jpg)
